A facile and environmentally friendly method is proposed to prepare reduced graphene oxide–nickel (RGO–Ni) nanocomposites using γ-ray irradiation. Graphene oxide (GO) and Ni²⁺ are reduced by the electrons which originated from the gamma radiolysis of H₂O. The structure and morphology of the obtained RGO–Ni nanocomposites were analyzed using X-ray diffraction (XRD) and Raman spectroscopy. The results show that Ni nanoparticles were dispersed uniformly on the surface of the RGO nanosheets. As expected, the combination of RGO nanosheets and Ni nanoparticles improved the electromagnetic wave absorption because of the better impedance matching. RGO–Ni nanocomposites exhibited efficient electromagnetic wave absorption performance. The minimum reflection loss (RL) of RGO–Ni reached −24.8 dB, and the highest effective absorption bandwidth was up to 6.9 GHz (RL < −10 dB) with a layer thickness of 9 mm.

T154 modified graphene oxide as an oil additive exhibited excellent tribological properties, long-term stable dispersity and high thermal properties.

A low infrared emissivity coating was prepared using graphene surface-modified flaky aluminum complex powders (rGO-FAl) as fillers. The flaky aluminum powders were coated with graphene through chemical bonding. Compared with pure flaky aluminum, the Vis-NIR diffuse reflectance of rGO-FAl complex powders was significantly decreased, which was beneficial to the low glossiness of the coating. After the modification, the glossiness at 60° of the coating with 40% (mass fraction) pigments decreased from 12.8 to 6.7, while the coating maintained low infrared emissivity (0.238~0.247) at a spectral range of 8–14 μm. In the electrochemical impedance spectroscopy (EIS) measurement, at the lowest frequency, the impedance of the Al-rGO test plate was at least two orders of magnitude greater than that of the control Al test plate, and the graphene layer significantly increased the bandwidth of the maximum phase angle, which indicates a good protective effect of the ultra-thin graphene layer on metal in a corrosive environment. The coating with 40% rGO-FAl complex powders can maintain its appearance after 500 h of salt spray corrosion testing. In contrast, the color of the coating with the original aluminum powders changed after only 300 h.

Octadecylamine (ODA) can solve the aggregation problem of graphene sheets in the chemical exfoliation method. However, no attempts have been made to investigate the evolution of ODA–reduced graphene oxide (ORGO) with reaction conditions and the modification mechanism, which is the core problem to realize the controllable production and practical application of graphene. In this study, we treated graphene oxide (GO) with ODA under different reaction conditions to prepare ORGO. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy, atomic force microscopy, Raman spectroscopy, thermogravimetric analysis (TGA), and UV–vis spectrophotometry were employed to analyze the composition, structure, morphology and characteristics of the as–prepared graphene sheets. The results showed that the reduction reaction could occur under mild conditions, but the edge grafting reaction could only be activated by a higher temperature. Moreover, the ORGO created at 80 °C for 5 h and 120 °C for 0.5 h exhibited the optimized properties, both excellent dispersing stability and high heat resisting property, since they had more edge grafting chains and a suitable reduction degree.

Zirconium oxide (ZrO₂) is widely used as the thermal barrier coating in turbines and engines. Accurate emissivity measurement of ZrO₂ coating at high temperatures, especially above 1000 °C, plays a vital role in thermal modelling and radiation thermometry. However, it is an extremely challenging enterprise, and very few high temperature emissivity results with rigorously estimated uncertainties have been published to date. The key issue for accurately measuring the high temperature emissivity is maintaining a hot surface without reflection from the hot environment, and avoiding passive or active oxidation of material, which will modify the emissivity. In this paper, a novel modified integrated blackbody method is reported to measure the high temperature normal spectral emissivity of ZrO₂ coating in the temperature range 1000 °C to 1200 °C and spectral range 8 μm to 14 μm. The results and the associated uncertainty of the measurement were estimated and a relative standard uncertainty better than 7% (k = 2) is achieved.