Thermoplastic composites are growing in popularity in the aerospace and automotive industries; they enable weldable and recyclable structures. Resistance welded hybrid thermoplastic and metal joints are attractive for rapid assembly, but the thermal mismatch between metals and polymers introduces residual stresses, which can drive edge debonding and compromise durability. This study presents fabricated single-lap PC/CF–Al7075 coupons with measured mid-span bow resulting from welding, evaluated bond quality by step-heating thermography, and an evaluated framework for residual stress prediction using Ansys complemented by a bimetal analytical check. Three thermal cycles were examined with different temperature gradients (200, 220, 240 °C): the measured bow was 16.5 mm and remained constant, whereas analytical calculation increased with ΔT similarly to the FEM prediction. The current FEM under predicted the bow (Mean Absolute Percentage Error is 21%), showing stress contours that decay with distance from the bond and revealing pronounced peaks in both σxx and σzz components at weld edges, consistent with shear-lag theory. FEM returned edge-peaked peel rising from 43 to −64 MPa and σxx was up to 12% more compressive than analytical calculation; an effective CF/PC CTE of 1.5 × 10−6 K−1 reconciled curvature with test better than catalogue values. The temperature insensitive bow is attributed to polycarbonate flow/viscoelastic relaxation above Tg and hot relaxation in aluminum, with effects not represented in the elastic models. Edge peel and shear govern initiation risk.
Thermoplastic composites enable weldable, recyclable aircraft structures, but thermal mismatch between metals and polymers can introduce detrimental residual stresses. This study develops a finite element method (FEM) framework to predict residual stress fields in resistance-welded joints between aluminum 7075 and carbon-fiber-reinforced polyamide 6 (PA6). Transient thermal analyses with multilinear, temperature-dependent properties were coupled to mechanical analyses; contact conditions transitioned from frictional to bonded at PA6 melting. Three thermal cycles (20°C→220°C→20°C, 20°C→240°C→20°C, 20°C→260°C→20°C) were examined to assess peak-temperature effects. The simulations show stress contours that decay with distance from the bond and reveal pronounced peaks in both normal and shear components at weld edges, consistent with shear-lag theory. Within the bonded interior, average stresses are relatively low, whereas edge concentrations identify likely sites for debonding or delamination initiation. The magnitude of residual stresses increases with thermal gradient, underscoring the need for parameter control during welding. The FEM outputs will be validated against uniaxial tension and three-point bending tests on welded specimens, with future work quantifying fatigue-life reduction under combined thermal and mechanical cycling. The results highlight mitigation priorities for bonded repairs and hybrid aerospace structures, including process-curve tuning (current/pressure/cooling) and edge-region design measures.
1 September 2026 in Transactions on Aerospace Research
Resistance-welded thermoplastic composite-metal hybrid joints may be useful for temporary or secondary aerospace repair concepts, but their small-coupon response is difficult to interpret because bending, peel, sliding and welding-induced residual stresses occur simultaneously. This paper presents an adapted three-point-bending study of six single-lap coupons made from carbon-fiber-reinforced polycarbonate and aluminum 7075. The test was used as a screening method to determine global stiffness, peak force and debonding behavior under a concentrated transverse load. The recorded force was converted to a nominal bending stress indicator using the test geometry. Peak forces ranged from 246.1 N to 293.7 N, with a mean value of 274.0 N. The corresponding nominal bending stress indicator ranged from 131.8 MPa to 157.3 MPa, with a mean value of 146.8 MPa. The apparent work per overlap area ranged from 0.615 mJ/mm 2 to 0.804 mJ/mm 2 . The area under the force-displacement curve was not treated as fracture energy because it also includes adherend bending, contact work and residual-stress release. The calculated stress-displacement curves were used to calibrate an ANSYS cohesive-zone debonding model. The welding-induced residual state was introduced through an initial strain condition before mechanical loading. The calibrated model predicted a peak stress of approximately 156 MPa, corresponding to approximately 291 N. This value was about 6.3% above the experimental mean and remained within the experimental range.