Jonathan Petticrew

Dr. Jonathan Petticrew

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 December 2017 in IEEE Journal of Selected Topics in Quantum Electronics
Verified
Journal Article
Open access
JPJonathan Petticrew
Jonathan Petticrew
SDSimon J. Dimler
Simon J. Dimler
XZXinxin Zhou
Xinxin Zhou
Alan MorrisonAlan Morrison
Alan Morrison
CTChee Hing Tan
Chee Hing Tan
JNJo Shien Ng
Jo Shien Ng
Silicon-based single photon avalanche diodes (SPADs) are widely used as single photon detectors of visible and near infrared photons. There has, however, been a lack of models accurately interpreting the physics of impact ionization (the mechanism behind avalanche breakdown) for these devices. In this paper, we present a statistical simulation model for silicon SPADs that is capable of predicting breakdown probability, mean time to breakdown, and timing jitter. Our model inherently incorporates carriers' dead space due to phonon scattering and allows for nonuniform electric fields. Model validation included avalanche gain, excess noise factor, breakdown voltage, breakdown probability, and timing statistics. Simulating an n-on-p and a p-on-n SPAD design using our model, we found that the n-on-p design offers significantly improved mean time to breakdown and timing jitter characteristics. For a breakdown probability of 0.5, mean time to breakdown and timing jitter from the n-on-p design were 3 and 4 times smaller compared to those from the p-on-n design. The data reported in this paper are available from the ORDA digital repository (DOI: 10.15131/shef.data.4823248).

9 May 2022 in Optics Express
Verified
Journal Article
Open access
JTJonathan Taylor-Mew
Jonathan Taylor-Mew
JPJonathan Petticrew
Jonathan Petticrew
CTChee Hing Tan
Chee Hing Tan
JNJo Shien Ng
Jo Shien Ng
Al0.85Ga0.15As0.56Sb0.44 is a promising avalanche material for near infrared avalanche photodiodes (APDs) because they exhibit very low excess noise factors. However electric field dependence of ionization coefficients in this material have not been reported. We report a Simple Monte Carlo model for Al0.85Ga0.15As0.56Sb0.44, which was validated using reported experimental results of capacitance-voltage, avalanche multiplication and excess noise factors from five APDs. The model was used to produce effective ionization coefficients and threshold energies between 400–1200 kV.cm-1 at room temperature, which are suitable for use with less complex APD simulation models.

17 October 2019 in Journal of Lightwave Technology
Verified
Journal Article
Open access
JPJonathan Petticrew
Jonathan Petticrew
SDSimon J. Dimler
Simon J. Dimler
CTChee Hing Tan
Chee Hing Tan
JNJo Shien Ng
Jo Shien Ng
Avalanche photodiodes (APDs), and single photon avalanche diodes (SPADs), with InP avalanche regions and InGaAs absorption regions, are used for detecting weak infrared light at ~ 1.55 μm wavelength. These devices are often cooled to below room temperature during operation yet both validated simulation models and impact ionization coefficients that accurately describe the avalanche characteristics of InP are lacking in the temperature range of interest (200 K to room temperature). In this paper we present an accessible, validated temperature dependent simulation model for InP APDs/SPADs. The model is capable of simulating avalanche gain, excess noise, breakdown voltage, and impulse current at 150 - 300 K. Temperature dependent ionization coefficients in InP, which may be used with other APD/SPAD simulation models, are also presented. The data reported in this paper is available from the ORDA digital repository (DOI: to be added prior to publication).

15 March 2019 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
LLLeh Woon Lim
Leh Woon Lim
CTChee Hing Tan
Chee Hing Tan
JNJo Shien Ng
Jo Shien Ng
JPJonathan Petticrew
Jonathan Petticrew
AKAndrey Krysa
Andrey Krysa
Indium Arsenide (InAs) infrared photodiodes provide high quantum efficiency in the wavelength range of 1.0-3.0 μm. Planar diode configuration has been adopted to reduce surface leakage. In this work, new fabrication procedures for planar InAs avalanche photodiodes (APDs) are reported. Beryllium (Be) ions were implanted into InAs at a relatively low energy of 34 keV. Effects of duration of post implant annealing on the electrical characteristics of InAs APDs were investigated. It was found that a combination of post implant annealing at 500 °C for 15 min and a shallow surface etch produces planar APDs with good characteristics (room temperature dark current density of 0.52 A/cm 2 at -0.2 V and external quantum efficiency of 51% at 1520 nm at -0.3 V). These represent a 3 times reduction in dark current and 1.4 times increase in responsivity, compared to earlier Be-implanted planar InAs APDs. The APDs' avalanche gain characteristics remain similar to those from earlier reports, with a gain of 4 at a relatively low operating bias of 5 V. This suggests the potential of integrating InAs APDs with low voltage readout integrated circuits (ROIC) for development of infrared imaging arrays. The data reported in this paper is available from the ORDA digital repository (DOI: 10.15131/shef.data.6955037).

23 December 2022 in Semiconductor Science and Technology
Verified
Journal Article
Open access
PDF file
JPJonathan Petticrew
Jonathan Petticrew
YJYuting Ji
Yuting Ji
IHIm Sik Han
Im Sik Han
BWBenjamin White
Benjamin White
AEAxel Evirgen
Axel Evirgen
JNJo Shien Ng
Jo Shien Ng
InGaAs/GaAsSb type-II superlattice (T2SL) photodiodes grown on InP substrates are an alternative detector technology for applications operating in the short wavelength infrared band. Their cut-off wavelengths are heavily influenced by the thickness and material composition of InGaAs and GaAsSb used in the T2SL. We present a single band k.p. model performed using a finite difference approach in nextnano validated against two T2SL photodiode wafers and results from literature. These photodiode wafers cover both lattice matched and strained GaAs1−x Sb x compositions (x = 0.40, wafer A and 0.49, wafer B). The validation data covers temperature dependence of cut-off wavelengths (obtained from phase-sensitive photo response data) from 200 K to room temperature. The cut-off wavelengths were found to reduce at 1.32 nm K−1 for wafer A and 1.07 nm K−1 for wafer B. Good agreement was achieved between the validation data and nextnano simulations, after altering the GaAs1−x Sb x valance band offset (VBO) bowing parameter to −1.06 eV. Using this validated model, we show that the wavefunction overlap drops significantly if the GaAsSb barrier is thicker than the InGaAs well layer, hence defining the upper limit of the barrier layer. This validated model is then used to demonstrate that there is a linear dependence between the maximum achievable wavefunction overlap and cut-off wavelength of a lattice matched InGaAs/GaAsSb T2SL. We also found that the adoption of a 5 nm/3 nm InGaAs/GaAsSb T2SL structure offers an improved wavefunction overlap over the more common 5 nm/5 nm InGaAs/GaAsSb T2SL designs. The data reported in this paper is available from doi: 10.15131/shef.data.20310591.

8 January 2018 in Journal of Open Research Software
Verified
Journal Article
Open access
PDF file
JPJonathan Petticrew
Jonathan Petticrew
SDSimon J. Dimler
Simon J. Dimler
JNJo Shien Ng
Jo Shien Ng