Can Luo

Dr. Can Luo

Harbin Institute of Technology, Harbin, Heilongjiang, China
orcid

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 September 2026 in Materials
Verified
Journal Article
Open access
PDF file
Lei LuoLei Luo
Lei Luo
CLCan Luo
Can Luo
QLQi Lv
Qi Lv
XLXiao Liang
Xiao Liang
Liang WangLiang Wang
Liang Wang
BWBinbin Wang
Binbin Wang
Aluminum–copper alloys, typified by ZL205A (AlCu5MnTiCdV, GB/T 1173), pose severe casting challenges due to their wide solidification interval, poor fluidity, and susceptibility to gas porosity and shrinkage defects. This study introduces a negative-pressure frozen sand mold casting process as a solution to these challenges and systematically quantifies its thermal and microstructural advantages over conventional resin sand and atmospheric frozen sand casting. Using inverse heat conduction analysis of multi-point thermocouple data, the interfacial heat transfer coefficient (IHTC) was quantitatively determined for 14 experimental conditions varying in mold type, pressure level, moisture content (2–6 wt.%), and initial freezing temperature (−20 to −40 °C). The results demonstrate that negative pressure combined with frozen sand molds (6 wt.% moisture, −40 °C) produces the highest active-period average IHTC of 236 W/(m2·K), representing a 2.8-fold increase over atmospheric frozen sand casting and a 1.6-fold increase over negative-pressure resin sand casting. This enhanced thermal driving force promotes grain refinement and effective gas removal, yielding superior mechanical properties: tensile strength of 200.6 MPa and elongation of 9.3% in the as-cast state, and 478.5 MPa and 7.4% after T6 heat treatment. Using the optimized process parameters, a thin-walled cabin component (Ø180 mm × 300 mm, minimum wall thickness 3 mm) was successfully fabricated without defects. These findings establish quantitative process–thermal–microstructure–property relationships for negative-pressure frozen sand casting of wide-solidification-interval aluminum alloys.

23 April 2026 in Polymer Composites
Verified
Journal Article
Closed access
CLCan Luo
Can Luo
JZJing‐Hua Zheng
Jing‐Hua Zheng
YSYaxing Song
Yaxing Song
JXJiaxun Xu
Jiaxun Xu
YCYiwei Chen
Yiwei Chen
XHXiaobo Han
Xiaobo Han

16 January 2026 in Research Square
Verified
Preprint
Open access
PDF file
QLQi Lv
Qi Lv
CLCan Luo
Can Luo
Lei LuoLei Luo
Lei Luo
XLXiao Liang
Xiao Liang
LWLiang Wang
Liang Wang
YSY.Q. Su
Y.Q. Su
The control of chemical composition remains the single most formidable challenge restricting the industrial adoption of Additive Manufacturing (AM) for high-volatility-contrast multicomponent alloys like TiAl. The extreme energy density utilized in powder bed fusion or directed energy deposition processes, exemplified here by the electron beam directed energy deposition (EB-DED) technique, triggers severe selective evaporation of volatile components, fundamentally compromising alloy design fidelity. This study presents a paradigmatic shift in AM process modeling by establishing a robust composition-prediction framework. We first analytically establish that Al selective evaporation is the dominant mechanism (Al vapor pressure is 1-2 orders of magnitude higher than Ti), and that the mass loss rate is kinetically controlled by the gas-liquid interface reaction ( K m << β m ). To resolve the non-uniformity inherent to the AM melt pool, we developed an advanced model that integrates fluid-dynamic predictions of melt flow with interface kinetics. This model uniquely accounts for the formation of distinct surface regimes: flow-induced solute-enriched regions (laminar flow) and a surrounding compositionally uniform region (vortex flow). The resulting model, incorporating both the non-uniform temperature field and the heterogeneous solute concentration, successfully forecasts the final alloy chemistry. The model demonstrates exceptional predictive robustness, achieving an experimental deviation of less than 2 at. % when compared to measurements. Based on this validated framework, an optimal processing window (20– 30 mA beam current; 1.5– 2.5 mm/s deposition speed) is defined. This work provides the necessary theoretical foundation and predictive toolset for achieving high compositional fidelity in the additive manufacturing of all alloys susceptible to severe elemental volatilization.