Meng Liu

Dr. Meng Liu

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 June 2022 in IEEE Internet of Things Journal
Verified
Journal Article
Closed access
KTKuanfeng Tang
Kuanfeng Tang
MWMaodong Wang
Maodong Wang
MLMeng Liu
Meng Liu
CZChao Zhang
Chao Zhang
SXShengliang Xu
Shengliang Xu
JMJin Mitsugi
Jin Mitsugi
This paper introduces a highly integrated passive wireless sensing system based on extended EPC Gen2 protocol, using sensor tags and a reader to support concurrent data streams from multiple sensors. Multiple Subcarrier Multiple Access (MSMA) is used by assigning different subcarrier frequencies to the sensor tags for backscattering so that each tag has an independent channel for communication to achieve the simultaneous streaming of multi-sensor data. In order to improve the subcarrier frequency accuracy and further increase the number of communication channels, this paper proposes a novel method of subcarrier frequency calibration based on the Gen2 protocol. This method enables a high accuracy clock to be generated on-chip. At the same time, this paper also proposes a method based on Gen2 protocol to start a group of tags and receive real-time data in parallel. The tag chip is fabricated in a 0.18 μm CMOS process with a die size of 850 μm × 850 μm, and the reader prototype is built using software-defined radio equipment. The test results show that the sensing system proposed in this paper can collect and recognize concurrent data streams from multiple sensor tags synchronously. The measured sensitivity of the sensor tag is -14.9dBm with a 3-axis accelerating sensor, and the calibration accuracy of subcarrier frequency is better than ±0.385KHz in the range of 40KHz-640KHz. With this accuracy, the tags can be allocated up to 78 subcarrier communication channels theoretically.

13 November 2025 in Electronics
Verified
Journal Article
Open access
PDF file
MLMeng Liu
Meng Liu
The rapid development of the Internet of Things (IoT) has imposed increasingly stringent power consumption requirements on receiver design. Unlike phase-locked loops (PLLs), free-running oscillators eliminate power-hungry loop circuitry. However, the inherent frequency offset of free-running oscillators introduces uncertainty in the intermediate frequency (IF), preventing the receiver from aligning with the desired channel. To address this, we present a reconfigurable channel receiver employing a free-running oscillator and frequency estimation for low-power IoT applications. The proposed receiver first captures a specific preamble sequence corresponding to the desired channel through multiple parallel sub-channels implemented in the digital baseband (DBB), which collectively cover the expected IF frequency range. The desired IF frequency is estimated using the proposed preamble-based frequency estimation (PBFE) algorithm. After frequency estimation, the receiver switches to a single-channel mode and tunes its passband center frequency to the estimated IF frequency, enabling high-sensitivity data reception. Measurement results demonstrate that the PBFE algorithm achieves reliable frequency estimation with a minimum IF signal-to-noise ratio (SNR) of 2 dB and an estimation error below 22 kHz. In single-channel mode, with a residual frequency offset of 30 kHz, an 8-point energy accumulation decoding scheme achieves a bit error rate (BER) of 10−3 at an IF SNR of 5.2 dB. Compared with the case of the original 50 kHz IF frequency offset, the required SNR is improved by 4.1 dB.

18 July 2024 in IEEE Access
Verified
Journal Article
Open access
SLSijia Lai
Sijia Lai
YZYuxiao Zhao
Yuxiao Zhao
MLMeng Liu
Meng Liu
SXShengliang Xu
Shengliang Xu
KTKuangfeng Tang
Kuangfeng Tang
HMHao Min
Hao Min
Owing to the rapid development of the ambient Internet of Things (IoT) industry, Backscatter Communication Systems (BCS) require higher receiver sensitivity for large-scale IoT scenarios than traditional Radio Frequency Identification (RFID) systems. This paper proposes a method of using Multiple-Input Multiple-Output (MIMO) technology to compensate for reflected signals in the 920 MHz backscatter communication systems. The researcher first created a MATLAB model to verify the theoretical feasibility and then built a One-Transmitter Two-Receiver (1T2R) BCS transceiver system compatible with the EPC global protocol for practical verification on LabVIEW. The ITIR and 1T2R tests were conducted using the National Instrument (NI) USRP-2952R device, the directional antennas, and the standard RF electronic tags. Through the process of superimposing and utilizing the phase shift between the two reflected carriers, it has been confirmed that the overall signal strength can be enhanced from 2.2 mV to 4.13 mV and 4.37 mV (nearly reaching 4.70 mV by using two Rx antennas in ideal conditions). After calculation, this advancement increases signal strength from -40.14 dBm (when using a single Rx antenna) to -34.18 dBm (when using two Rx antennas). The improvement in signal strength can provide a gain of 5.96 dB to the backscatter communication systems. Experimental results demonstrate that utilizing MIMO technology to the backscatter communication systems can effectively enhance the sensitivity of the receiver at 920 MHz.