In this study, drug carrier nanoparticles comprised of Pluronic-F127 and cannabidiol (CBD) or cannabigerol (CBG) were developed, and their wound healing action was studied. They were further incorporated in 3D printed films based on sodium alginate. The prepared films were characterized morphologically and physicochemically and used to evaluate the drug release profiles of the nanoparticles. Additional studies on their water loss rate, water retention capacity, and 3D-printing shape fidelity were performed. Nanoparticles were characterized physicochemically and for their drug loading performance. They were further assessed for their cytotoxicity (MTT Assay) and wound healing action (Cell Scratch Assay). The in vitro wound-healing study showed that the nanoparticles successfully enhanced wound healing in the first 6 h of application, but in the following 6 h they had an adverse effect. MTT assay studies revealed that in the first 24 h, a concentration of 0.1 mg/mL nanoparticles resulted in satisfactory cell viability, whereas CBG nanoparticles were safe even at 48 h. However, in higher concentrations and after a threshold of 24 h, the cell viability was significantly decreased. The results also presented mono-disperse nano-sized particles with diameters smaller than 200 nm with excellent release profiles and enhanced thermal stability. Their entrapment efficiency and drug loading properties were higher than 97%. The release profiles of the active pharmaceutical ingredients from the films revealed a complete release within 24 h. The fabricated 3D-printed films hold promise for wound healing applications; however, more studies are needed to further elucidate their mechanism of action.

In the present study, a chitosan (CS) derivative with the 2-(Methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (SDAEM) zwitterionic monomer was prepared through chemical modification. The successful synthesis of CS-SDAEM was confirmed by Fourier-transform Infrared (FTIR) and Nuclear Magnetic Resonance (¹H-NMR) spectroscopies. Its crystallinity was studied by X-ray Diffraction (XRD), while in vitro cytotoxicity and cell viability assays established its biocompatibility. Filtered fresh pomegranate juice (PJ) was loaded in nanoparticles of neat CS and its derivative via ionic gelation method. Dynamic Light Scattering (DLS) revealed nanoparticles sizes varying between 426 nm and 4.5 μm, indicating a size-dependence on the polymer concentration used during encapsulation. High-performance liquid chromatography coupled with photodiode array and electrospray ionization mass spectrometry detection (LC-PDA-ESI/MS) revealed that PJ active compounds were successfully and in sufficient amounts encapsulated in the nanoparticles interior, whereas XRD indicated a crystalline structure alteration after nanoencapsulation. The resulted PJ-loaded nanoparticles were further utilized for the preparation of innovative O/W cosmetic emulsions. All produced emulsions exhibited good pH and viscosity stability for up to 90 days, while the sun protection factor (SPF) was enhanced due to the presence of the PJ. Enhanced antioxidant and antimicrobial properties due to the phenolic compounds of PJ were also observed.

The aim of the present study was to prepare a leflunomide (LFD) sustained release transdermal delivery system for the treatment of psoriasis. In this context, LFD-loaded nanoparticles (NPs) based on either neat chitosan (CS) or CS modified with [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (SDAEM, a sulfobetaine zwitterionic compound) were initially prepared via ionotropic gelation and characterized in terms of in vitro dissolution, physicochemical, and antibacterial properties. Results showed that the use of the SDAEM-modified CS resulted in the formation of LFD-loaded NPs with improved wetting and solubilization properties, better in vitro dissolution profile characteristics (i.e., higher dissolution rate and extent), and improved (enhanced) antibacterial properties. The resultant LFD-loaded NPs were then embedded in suitable thin-film skin patches, prepared via spin-coating, utilizing two different biodegradable polyesters, namely methoxy polyethylene glycol-b-poly(L-lactide) (mPEG-b-PLA, at a ratio of 25/75 mPEG to PLA) and poly(lactic-co-glycolic acid) (PLGA at a ratio of 75/25 DL-lactide/glycolide copolymer). Results showed the formation of polymeric thin-films with no agglomeration (or trapped air) and uniform structure in all cases, while the LFD-loaded NPs were successfully embedded in the polymeric matrix. Analysis of the obtained in vitro dissolution profiles revealed a sustained release profile of the drug for up to approximately twelve days, while between the two proposed systems, the use of CS-SDAEM NPs (independently of the polyester type) was the most promising formulation approach.