CO2 and N2 injection is an effective enhanced oil recovery technology in the oilfield especially for low-permeability and extra low-permeability reservoirs. However, these processes can induce an asphaltene deposition during oil production. Asphaltene-deposition-induced formation damage is a fairly severe problem. Therefore, predicting the likelihood of asphaltene deposition in reservoir conditions is crucial. This paper presents the results of flash separation experiments used to investigate the composition of crude oil in shallow and buried-hill reservoirs. Then, PVTsim Nova is used to simulate the composition change and asphaltene deposition of crude oil. Simulation tests indicate that the content of light components C1-C4 and heavy components C36+ decrease with increasing CO2 and N2 injection volumes. However, the extraction of CO2 is significantly stronger than that of N2. In shallow reservoirs, as the CO2 injection volume increases, the deposition pressure range decreases and asphaltenes are easily deposited. Conversely, the asphaltene deposition pressure of crude oil injected with N2 is higher and will not cause serious asphaltene deposition. When the CO2-N2 injection ratio reaches 1:1, the deposition pressure range shows a significant transition. In buried-hill reservoirs, asphaltene deposition is unlikely to occur with CO2, N2, and a gas mixture injection.
CO2 huff-n-puff is regarded as an effective method to improve the recovery of low permeability and tight oil reservoirs. To understand the impact of CO2 huff-n-puff on crude oil mobilization in tight reservoirs with different fracture scales, this study conducted CO2 huff-n-puff nuclear magnetic resonance (NMR) and microscopic visualization experiments, focusing on how varying fracture apertures and densities affect the efficiency of the CO2 huff-n-puff. The results show that in scenarios with a single fracture, larger fracture apertures significantly boost oil mobilization within the fracture and the surrounding matrix. For instance, increasing the aperture from 20 μm to 70 μm improved the recovery factor by 9.20%. In environments with multiple fractures, greater fracture density enhances reservoir connectivity, and increases the CO2 sweep area, and the complex fracture model shows a 4.26% increase in matrix utilization compared to the simple fracture model. Notably, the improvement in recovery due to multi-scale fractures is most significant during the first two huff-and-puff cycles, with diminishing returns in subsequent cycles. Overall, increasing both fracture size and density effectively enhances crude oil mobilization in tight reservoirs. These findings provide valuable insights into improving the recovery efficiency of CO2 huff-and-puff techniques in tight oil reservoirs.
Carbon dioxide (CO2) is being considered for use to enhance oil recovery and resource utilization and storage, with wide technical adaptability. In this paper, a numerical simulation method is used to study the adaptability of CO2 huff and puff in shale reservoirs. A fluid model introduces the nanoconfinement effect and reflects the nanoconfinement effect using the fluid p–T phase diagram. This method uses local grid refinement and changes the permeability near the grid to characterize the reservoir reconstruction volume (SRV) fracture network while considering the CO2 diffusion effect. The results indicate that by using the incremental recovery rate and oil change rate as references, adaptive charts can be obtained for different Kf/Km and oil saturation. When Kf/Km is 1000 and the increase in the CO2 recovery rate reaches 1.5%, the lower limit of oil saturation is 0.54. When Kf/Km is 1000 and the increase in the CO2 recovery rate reaches 2%, the lower limit of oil saturation is 0.57. When the oil saturation is 0.5 and the CO2 huff and puff oil change rate reaches 0.3, the lower limit of Kf/Km is 700. Finally, when the oil saturation is 0.548 and the CO2 huff and puff oil change rate reaches 0.6, the lower limit of Kf/Km is 10. The research results are significant and can guide the design and application of on-site CO2 throughput test plans.
Injecting CO2 into tight oil reservoirs is a potential approach for enhanced oil recovery (EOR) and CO2 sequestration. However, the effects of different pore-scales on EOR are poorly understood, and this has a significant impact on recovery. In this paper, a pore size correction model based on X-ray computerized tomography (CT) and nuclear magnetic resonance (NMR) was developed in order to establish the relationship between the pore radius and the transverse relaxation time. Different pore-scales are divided according to the cumulative distribution characteristics of the transverse relaxation time (T2). CO2 flooding and huff-n-puff experiments were conducted to investigate the dynamic displacement behaviors in different pore-scales. The results indicate that there are three pore-scales: micropores (T2 < 0.3 ms), intermediate pores (0.3 ms < T2 < 100 ms), and macropores (100 ms < T2). However, there are also pseudo-sweep pores (PPs), equilibrium pores (EPs), and sweep pores (SPs) in the intermediate pores, depending on whether crude oil has been produced. Interestingly, the pressurization process causes some crude oil in the large pores to be squeezed into small pores. The recovery of CO2 huff-n-puff (19.75%) is obviously lower than that of CO2 flooding (51.61%). Specifically, it was observed that the micropores (−8%) and the pseudo-sweep pores (−37%) have a negative impact on oil recovery, whereas all pore-scales exhibit positive effects during CO2 flooding. In addition, it was found that the critical pore radiuses of CO2 flooding and huff-n-puff were 2.61 ms (0.15 µm) and 25 ms (1.5 µm), respectively, in the experiments, and that there is also more oil remaining in the macropores and the sweep pores during CO2 huff-n-puff. These results provide a deeper understanding of the displacement behaviors of different pore-scales in tight oil reservoirs.
Tight oil reservoirs are characterized by poor petrophysical properties. After hydraulic fracturing, the low flowback rate of fracturing fluid readily leads to the formation of a water invasion zone in the near-wellbore region, which severely restricts the performance of Carbon dioxide (CO2) huff-n-puff. To clarify the damage mechanism of the water invasion zone on CO2 huff-n-puff in tight oil reservoirs and determine the key regulatory parameters, tight cores with a relative water invasion zone length Δδ = 0.3 were adopted as the research subject. Five groups of injection–soaking–production time combinations were designed, and single-factor analysis was implemented using the control variable method. Integrated with numerical simulation and nuclear magnetic resonance (NMR) testing, the influence of the water invasion zone, pore crude oil mobilization characteristics, and parameter regulation effects were systematically explored. The results demonstrate that the water invasion zone occupies effective pore throats to form a continuous water-phase barrier, hindering CO2 seepage and mass transfer. After four huff-n-puff cycles, the cumulative recovery factor of the water-invaded model is 4.13 percentage points lower than that of the water-free model. After four huff-n-puff cycles, the cumulative recovery factor of the water-invaded model is 4.13 percentage points lower than that of the water-free model. The NMR T2 spectra of cores with and without water invasion exhibit remarkable discrepancies: the water-free core presents a unimodal structure, while the water-invaded core features a distinctive bimodal structure, with obvious staged characteristics in crude oil mobilization. The recovery factor declines nonlinearly and sharply with the increase of Δδ, verifying that the water invasion zone length is the dominant controlling factor. The regulation effects of injection, soaking, and production time differ significantly: injection time serves as the pivotal parameter for enhancing oil recovery. Prolonging injection time can strengthen displacement intensity and dismantle the water-phase barrier, thereby elevating the recovery factor, whereas soaking time and production time have no significant improvement effect. The results can provide valuable references for the parameter optimization of CO2 huff-n-puff in water-invaded tight oil reservoirs.