CO2 huff-n-puff is regarded as an effective method to improve the recovery of low permeability and tight oil reservoirs. To understand the impact of CO2 huff-n-puff on crude oil mobilization in tight reservoirs with different fracture scales, this study conducted CO2 huff-n-puff nuclear magnetic resonance (NMR) and microscopic visualization experiments, focusing on how varying fracture apertures and densities affect the efficiency of the CO2 huff-n-puff. The results show that in scenarios with a single fracture, larger fracture apertures significantly boost oil mobilization within the fracture and the surrounding matrix. For instance, increasing the aperture from 20 μm to 70 μm improved the recovery factor by 9.20%. In environments with multiple fractures, greater fracture density enhances reservoir connectivity, and increases the CO2 sweep area, and the complex fracture model shows a 4.26% increase in matrix utilization compared to the simple fracture model. Notably, the improvement in recovery due to multi-scale fractures is most significant during the first two huff-and-puff cycles, with diminishing returns in subsequent cycles. Overall, increasing both fracture size and density effectively enhances crude oil mobilization in tight reservoirs. These findings provide valuable insights into improving the recovery efficiency of CO2 huff-and-puff techniques in tight oil reservoirs.
Lab experiments, field pilots, and numerical modeling focusing on fluid flow aspects have indicated that multi-branch wells are technically effective and promising. Several researchers have conducted some experiments for a fishbone well strategy with mixed results. Our objective in this work is to study the impact of the different fishbone well patterns, such as branch angle, on the distribution of remaining oil after water flooding. In this paper, the interference effect between branches on oil recovery is studied in three steps. First, the interferences between fishbone wells with different branch angles were measured by hydro-electric simulation experiments. Second, two-dimensional visualization water flooding experiments were carried out to clarify the remaining oil distribution at different branch angles. Third, the distribution of oil and water in fishbone wells was verified by establishing a numerical model. The modeling results agree well with the experimental phenomena. At the same time, the variation trend of water and oil production in each branch is analyzed by numerical simulation results. The results indicate that the production is strongly dependent on the branch angles, and the highest recovery was 60.2% at a 45° branch angle.
This paper presented a novel numerical method for estimating the gas diffusion coefficient based on the early-time pressure-decay data. Experimentally, “flooding–soaking” procedures were developed to perform the gas diffusion in an oil-saturated tight core under different gas phase volume conditions. After flooding, the capillary bundle model was used to calculate the oil–gas contact area. The early-time pressure-decay data of the gas phase were monitored and recorded during the soaking process. Theoretically, a non-equilibrium inner boundary condition coupled with the characteristics of experimental early-time pressure had been incorporated to develop a diffusion model for a gas/oil-saturated tight core system. Based on gas-phase mass balance equations and gas equation of state, the diffusion coefficients were optimized once the discrepancy between experimental data and numerical solutions was minimized. According to the estimated results in this study, the CH4 diffusion coefficients were 3.74 × 10−11 and 3.86 × 10−11 m2/s in tight core saturated with crude oil, respectively. Moreover, the oil–gas contact area significantly impacts the diffusion flux in oil-saturated porous media. Specifically, an additional 10% contact area results in a 75% increase in CH4 diffusion mass. In addition, with the application of our proposed model to CH4/bitumen and CO2/bitumen systems, the diffusion coefficients were in close agreement with the results reported in previous literature, indicating that the proposed model was applicable to both gas/liquid and gas/liquid-saturated porous media systems.
Injecting CO2 into tight oil reservoirs is a potential approach for enhanced oil recovery (EOR) and CO2 sequestration. However, the effects of different pore-scales on EOR are poorly understood, and this has a significant impact on recovery. In this paper, a pore size correction model based on X-ray computerized tomography (CT) and nuclear magnetic resonance (NMR) was developed in order to establish the relationship between the pore radius and the transverse relaxation time. Different pore-scales are divided according to the cumulative distribution characteristics of the transverse relaxation time (T2). CO2 flooding and huff-n-puff experiments were conducted to investigate the dynamic displacement behaviors in different pore-scales. The results indicate that there are three pore-scales: micropores (T2 < 0.3 ms), intermediate pores (0.3 ms < T2 < 100 ms), and macropores (100 ms < T2). However, there are also pseudo-sweep pores (PPs), equilibrium pores (EPs), and sweep pores (SPs) in the intermediate pores, depending on whether crude oil has been produced. Interestingly, the pressurization process causes some crude oil in the large pores to be squeezed into small pores. The recovery of CO2 huff-n-puff (19.75%) is obviously lower than that of CO2 flooding (51.61%). Specifically, it was observed that the micropores (−8%) and the pseudo-sweep pores (−37%) have a negative impact on oil recovery, whereas all pore-scales exhibit positive effects during CO2 flooding. In addition, it was found that the critical pore radiuses of CO2 flooding and huff-n-puff were 2.61 ms (0.15 µm) and 25 ms (1.5 µm), respectively, in the experiments, and that there is also more oil remaining in the macropores and the sweep pores during CO2 huff-n-puff. These results provide a deeper understanding of the displacement behaviors of different pore-scales in tight oil reservoirs.
CO2 huff-n-puff (HnP) is an established enhanced oil recovery (EOR) method for shale oil reservoirs. However, its field-scale implementation in multiwell fractured systems remains challenging because fracture-controlled interwell connectivity can cause operational interference and inefficient CO2 allocation. A field-scale numerical model of the HH shale oil reservoir, incorporating complex natural and hydraulic fracture networks, was constructed and history-matched against field production data, followed by a structured sequential one-factor-at-a-time analysis and descriptive Spearman rank-correlation screening of the associations between operational parameters and performance indicators. Results indicate that, for the calibrated HH reservoir realization, the intragroup synchronized and intergroup asynchronous strategy achieved the highest cumulative incremental oil production among the investigated strategies (9.59 × 104 t), together with a CO2 utilization efficiency of 0.266 t oil/t CO2. This performance was associated with the cross-group pressure contrast observed under the asynchronous operation of the two well groups. Rank-correlation screening indicated that cycle number and cyclic CO2 injection mass showed the strongest associations with oil recovery and CO2 utilization efficiency, respectively, within the investigated cases. Within the investigated ranges and under the experimentally constrained diffusion setting of the calibrated HH reservoir model, 45 days and 450 t/d were identified as the preferred soaking time and injection rate, respectively. Extending the soaking time from 45 to 55 days yielded only marginal improvements, whereas increasing the injection rate from 450 to 600 t/d slightly reduced both incremental oil production and CO2 utilization efficiency. Furthermore, compared with the uniform injection scheme, the differentiated injection scheme maintained a comparable OOIP-based recovery factor (15.97% versus 15.84%) while reducing the cumulative gross CO2 injection mass from 36.0 × 104 to 33.1 × 104 t, corresponding to an 8.1% reduction. The EOR-oriented CO2 utilization efficiency consequently increased from 0.274 to 0.305 t oil/t CO2. Therefore, its principal benefit was the more efficient use of the injected CO2 rather than a substantial increase in ultimate oil recovery. This work provides a field-scale numerical workflow for designing and evaluating coordinated multiwell CO2 HnP operations in fractured shale oil reservoirs.