Shekhar Srivastava

Mr. Shekhar Srivastava


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2017 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
SSShekhar Srivastava
Shekhar Srivastava
RGR.K. Garg
R.K. Garg

30 October 2020 in Archives of Computational Methods in Engineering
Verified
Journal Article
Closed access
PDF file
SSShekhar Srivastava
Shekhar Srivastava
RGRajiv Kumar Garg
Rajiv Kumar Garg
VSVishal S. Sharma
Vishal S. Sharma
ASAnish Sachdeva
Anish Sachdeva


30 September 2022 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
SSShekhar Srivastava
Shekhar Srivastava
RGRAJIV KUMAR GARG
RAJIV KUMAR GARG
ASAnish Kumar Sachdeva
Anish Kumar Sachdeva
VSVishal Sharma
Vishal Sharma
Accumulated heat input during layer deposition causes high residual stress in the Wire-Arc Additive Manufacturing (WAAM) components. The developed residual stress results in defects like distortion, delamination, cracks, and low fatigue life. To deal with such engineering problems, numerical methods have always been required. It gives an insight into the system that can be used for real-world applications. Consequently, a sequentially coupled finite element model has been developed to simulate the thermal–structural behavior of the feedstock during and after deposition in the WAAM process. Precisely, a novel multi-level layer-wise heat input approach characterized by four different stages is compared with the layer-wise single heat input strategy. The variation of thermal and residual stress distributions has been studied based on the different cases proposed related to layer-wise multi-level heat loading. A good agreement between predicted and experimentally observed temperature and residual stress values has been observed. The developed framework predicted thermal distribution with an average error of 9.71%, 9.13%, 7.57%, and 4.52% for case #1, case #2, case #3, and case #4, respectively. In addition to that, longitudinal stresses in the modeled component recorded a reduction of 17.94% for four-level heat input (case #4) compared to the respective value observed in case #1. Therefore, a multi-level heat input strategy is recommended over a single-level heat input approach for the components with small deposition lengths manufactured through the WAAM process.

14 March 2020 in Rapid Prototyping Journal
Verified
Journal Article
Closed access
SSShekhar Srivastava
Shekhar Srivastava
RGRajiv Kumar Garg
Rajiv Kumar Garg
VSVishal Sharma
Vishal Sharma
NANoe Gaudencio Alba-Baena
Noe Gaudencio Alba-Baena
ASAnish Kumar Sachdeva
Anish Kumar Sachdeva
SSSehijpal Singh
Sehijpal Singh
Purpose: This paper aims to present a systematic approach in the literature survey related to metal additive manufacturing (AM) processes and its multi-physics continuum modelling approach for its better understanding.Design/methodology/approach: A systematic review of the literature available in the area of continuum modelling practices adopted for the powder bed fusion (PBF) AM processes for the deposition of powder layer over the substrate along with quantification of residual stress and distortion. Discrete element method (DEM) and finite element method (FEM) approaches have been reviewed for the deposition of powder layer and thermo-mechanical modelling, respectively. Further, thermo-mechanical modelling adopted for the PBF AM process have been discussed in detail with its constituents. Finally, on the basis of prediction through thermo-mechanical models and experimental validation, distortion mitigation/minimisation techniques applied in PBF AM processes have been reviewed to provide a future direction in the field.Findings: The findings of this paper are the future directions for the implementation and modification of the continuum modelling approaches applied to PBF AM processes. On the basis of the extensive review in the domain, gaps are recommended for future work for the betterment of modelling approach.Research limitations/implications: This paper is limited to review only the modelling approach adopted by the PBF AM processes, i.e. modelling techniques (DEM approach) used for the deposition of powder layer and macro-models at process scale for the prediction of residual stress and distortion in the component. Modelling of microstructure and grain growth has not been included in this paper.Originality/value: This paper presents an extensive review of the FEM approach adopted for the prediction of residual stress and distortion in the PBF AM processes which sets the platform for the development of distortion mitigation techniques. An extensive review of distortion mitigation techniques has been presented in the last section of the paper, which has not been reviewed yet.

2 August 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
RCRamesh Chand
Ramesh Chand
VSVishal Sharma
Vishal Sharma
RTRajeev Trehan
Rajeev Trehan
RVRajeev Verma
Rajeev Verma
MGMunish Gupta
Munish Gupta
SSShekhar Srivastava
Shekhar Srivastava
Superhydrophobicity is a surface property used in several sectors, including self-cleaning, drag reduction, improved buoyancy, and antibacterial behavior of the surfaces. The majority of available approaches for creating superhydrophobic surfaces (SHS) are complex and time-consuming. Goal: This article aims to fabricate the SHS by using Multi jet printer three-dimensional (3D) printing. Methods: The texture of cylindrical protrusions (diameter 300 Micro Meter (µm), pitch 400 and 500 µm) and pyramidical (side 200 µm, side by side distance 200 µm, and height 800 µm) micro-pattern were created using Three-Dimensional Printing (3DP) to achieve the SHS. Results: The fabricated geometries yielded a water contact angle of 145 and 148°, respectively. In order to enhance the durability and Water Contact Angle (WCA), 3D printed geometry was treated with an aqueous solution of silica nanoparticles and Hexafor 644-D, which increased the contact angles to 161 and 160° for cylindrical and pyramid patterns, respectively. The reported geometries are durable against peeling tape tests. Hence MJP, based on 3DP, can be used to fabricate the SHS having the geometries height in micron (µm).