We present baria-silica erbium-doped fibers (Ba-EDF) for extending the bandwidth of L-band EDFAs beyond 1620 nm. Using a combination of modified chemical vapor deposition (MCVD) process and solution-doping technique, we demonstrate low loss (<10 dB/km at 1200 nm) fiber cores with BaO concentration of 1-3 mol% and Er ³⁺ concentration of 8×10 ²⁴ m ^-3 . We show that the optical properties and EDFA performance are positively affected by increasing the BaO content. Namely, when we increase the BaO concentration from 1.3 to 3 mol%, we observe a reduction of pair-induced quenching that correlates with a bi-exponential luminescence decay with a dominant 15.5 ms lifetime component. Furthermore, the slight modifications of absorption/ emission coefficients point to a red-shift of the signal excited state absorption and consequently, to a moderate extension of the L-band gain to longer wavelengths (1622 nm).

Mode-locking is an ultra-short pulse laser generation technique. The range of pulse duration may vary from picoseconds to femtoseconds. Yttrium Oxide (Y₂O₃) based saturable absorber (SA) was appropriately revealed in the mode-locked method within the 1.55-micron regime. Y₂O₃ is perfect for strength, melting point, and chemical stability and can be used as a laminated insulator due to its properties. Moreover, Y₂O₃ also owns broadband service, switching speed, and engineering features. The Y₂O₃-PVA film was produced by combining the 50 mg Y₂O₃ powder into a 50 mL polyvinyl alcohol (PVA) solution and stirring it at room temperature for about 24 h. A mode-locked pulse was recorded with the integrated Y₂O₃-PVA SA in the erbium-doped fiber laser (EDFL) cavity, and the output spectrum optical spectrum analyzer displayed was around 1560.66 nm. In addition to the sustained mode-locked pulse, a nearly constant repetition rate of 1.01 MHz at a specific pump power begins from 175.87 mW to 228.04 mW while the pulse duration is 4.15 ps. Lastly, the mode-locked pulse had been evaluated, which showed the peak power started from 4.94 kW to 6.07 kW.

In this study, the gain clamping performance of Hafnia-bismuth-erbium co-doped fibre amplifier (HB-EDFA) using a lasing controlled structure with fibre Bragg grating (FBG) pair is presented. First, the gain and noise figure (NF) characteristics of a bidirectionally pumped HB-EDFA with very short lengths of heavily doped fibre are presented regarding its critical design parameters such as HB-EDF length, pump power, input signal power and signal wavelength. Then, the gain clamping performance of a bidirectionally pumped HB-EDFA having a C-band FBG pair with Bragg wavelengths of 1534 and 1542 nm is experimentally analysed. A good gain clamping capability was obtained using the proposed bidirectionally HB-EDFA design which has resulted in a dynamic signal input power range of 25 dB at 16 dB signal gain for 1.6 m HB-EDF length, and a wider dynamic signal input power range of 30 dB at 10 dB signal gain for 1.1 m HB-EDF length.

Fiber Bragg gratings (FBG) are ideal sensors for temperature, strain or vibration sensing applications with their advantages over conventional electronics sensor systems. In this paper, two different FBG sensor interrogation schemes based on broadband ASE source and tunable EDFRL source are demonstrated and compared. With both interrogator configurations, the response of the FBG sensor to temperature change is found to be linear and the sensitivities are measured as 11 pm/°C and 10.5 pm/°C, respectively. The experimental results have revealed that the optical power reflected from the FBG sensor is almost 20 dB higher with tunable EDFRL source than broadband ASE source. Thus, an interrogation method with tunable EDFRL can be suitable for remote, quasi-distributed sensor applications requiring high output power and OSNR.

In modern optical communication, the DWDM systems allow high-speed data transmission over long distances. The undesired phenomena like dispersion and nonlinearity of optical fiber affect the system performance and reduce the signal quality. This work examines improving DWDM system performance through EDFA and DCF strategies. An eight-channel DWDM system at 10 Gbps per channel is tested under different EDFA designs. The results showed that adding DCF to the system improves signal quality. Additionally, the booster amplifier setup performed better than other positions of EDFA in the optical link. Moreover, using a bidirectional pumping schema has a higher Q-factor average with more stability than a forward pumping configuration. Also, the pump wavelength at 1480 nm always achieved a good performance compared to 980 nm.