The increasing use of white LEDs for indoor illumination provides a significant opportunity for Visible Light Positioning (VLP). The challenge is to design a small, unobtrusive sensor that can be incorporated into mobile devices to provide accurate measurements for triangulation. We present experimental results for a novel angle of arrival (AOA) detector that has been designed for use in a VLP system. The detector is composed of a transparent aperture in an opaque screen that is located above a quadrant photodiode (PD), separated by a known vertical distance. Light passing through the aperture from an LED casts a light spot onto the quadrant PD. The position of this spot, coupled with knowledge of the height of the aperture above the quadrant PD, provides sufficient information to determine both the incident and polar angles of the light. Experiments, using a prototype detector, show that detector is capable of accurate estimation of AOA. The root mean square errors (rMSE) were less than 0.11° for all the measured positions on the test bed, with 90% of positions having an rMSE of less than 0.07°.
Visible light positioning (VLP), using LED luminaires as beacons, is a promising solution to the growing demand for accurate indoor positioning. In this paper, we introduce a two-stage receiver that has been specifically designed for VLP. This receiver exploits the advantages of two different VLP receiver types: photodiodes and imaging sensors. In this new receiver design a quadrant angular diversity aperture (QADA) receiver is combined with an off-the-shelf camera to form a robust new receiver called QADA-plus. Results are presented for QADA that show the impact of noise and luminaire geometry on angle of arrival estimation accuracy and positioning accuracy. Detailed discussions highlight other potential sources of error for the QADA receiver and explain how the two-stage QADA-plus can overcome these issues.
This paper describes a new form of angle of arrival (AOA) detector which can be applied in an indoor visible light positioning system using LED luminaires. In this new detector, a quadrant photodiode (PD) is placed below a transparent aperture in an opaque screen. Light passing through the aperture creates an illuminated area on the quadrant PD. This light spot has the same shape and size as the aperture. The position of the light spot on the PD depends on the AOA of the light. It is shown that this position can be determined by measuring the relative optical power of the light reaching each of the four quadrants of the PD. For the case of a square aperture and a square photodetector, a simple algorithm can be used to determine the x and y coordinates of the center of the light spot on the PD. From this, the AOA can be calculated. Simulations for an indoor visible light positioning system using LED luminaires and realistic parameters show that accurate AOA estimation is possible. If different luminaires transmit different orthogonal signals, digital signal processing can be used to separately estimate the received signal powers from each of the transmitting luminaires. Thus, this new detector has the potential to provide accurate three-dimensional positioning using a single quadrant PD.
The angular diversity aperture (ADA) receiver is a new form of optical wireless receiver which is made up of a number of receiving elements (REs) each consisting of a photodiode (PD) located below an aperture in an opaque screen. Previous work on the use of ADA receivers for visible light communication (VLC) analyzes only REs with round apertures and photodiodes with a limited range of parameters. This paper extends the analysis to calculate the channel gains for REs with for both round and square apertures and PDs and for more parameters. Graphs show how the gain varies as a function of the relative orientation of the transmitter and receiver for ten different designs. It is shown that the directionality of an RE depends on the offset of the PD from the aperture and that the field of view depends on the distance between the aperture and the PD. Detailed theoretical analysis and extensive simulation results demonstrate the bit error rate (BER) performance of receivers based on these ten designs in a multiple-input multiple-output (MIMO) VLC application. The round and square designs are found to have very similar BERs. It is shown that, even with high levels of shot noise, good BER results can be achieved throughout a typical scenario.
In this paper, we introduce a new two-stage receiver structure for visible light positioning (VLP) and a particular implementation of the new structure called the QADA-PLUS receiver. By using two sensors, one a photodiode (PD) based sensor and the other an image-based sensor, the new structure exploits the strengths of both technologies while avoiding their weaknesses. The QADA-PLUS uses a quadrant angular diversity aperture receiver (QADA) for the PD-based stage. The QADA has a very compact, planar structure suitable for incorporation in a smartphone or other small device and has been shown to provide good angular diversity in a proof-of-concept laboratory experiment. The QADA is also, unlike typical image sensors, able to reliably demodulate high frequency visible light signals. In this paper extensive simulation results for a range of typical indoor scenarios and realistic parameters show that the QADA has the potential to accurately estimate the polar and incident angle of light transmitted by LED luminaires. The average absolute error in estimation of incident angle was 0.0006° and for polar angle estimation was 0.005°. A limitation of these simulations is that it is assumed that the luminaires can be modelled as point sources and that the dimensions of the QADA are very precisely known. Incorporation of the QADA in the new two-stage QADA-PLUS receiver removes these limitations in two ways - the image-based receiver provides very accurate angle-of-arrival estimates and the use of visible reference points means that the QADA-PLUS is compatible with luminaires of any shape.
Visible Light Positioning (VLP) is an exciting new technology that has the potential to provide indoor positioning in a myriad of applications. Typically, VLP uses LED luminaires for positioning beacons and, like other positioning technologies, there is a requirement that sufficient beacons are available in the field of view (FOV) for triangulation. This can be challenging in many environments due to the luminaire placement and size. In this paper we investigate the use of luminaire reference points (LRPs) and hybrid imaging-photodiode (HIP) receivers to improve the reliability and robustness of VLP. LRPs are precisely defined points on a luminaire that can be recognised by the imaging sensor in a HIP receiver. We show that, by associating multiple LRPs with a single luminaire, it is possible to achieve positioning when only one luminaire is in the FOV of the receiver. We demonstrate, using the geometric dilution of precision, that low positioning errors can be achieved even when luminaire geometry and spacing is non-ideal.