In this paper, we analyze the performance of optical receivers using photodetectors (PDs) with two different fields of view (FOVs) in a multiple-input multiple-output optical wireless communication system which uses intensity modulation and direct detection. The novel aspect is that the PDs in the receiver do not all have the same FOV. It is shown that the use of PDs with different FOVs leads to an invertible channel matrix even when the PDs are closely spaced. Simulations for a typical indoor visible light communications scenario where LED lights are used as data transmitters show that the signal-to-noise ratios at the equalizer outputs are much higher than for a receiver of the same dimension where all the PDs have the same FOV. Good performance can be achieved with PDs located in a 3.5 cm by 3.5 cm area. Finally, the overall bit error rate (BER) is calculated for systems using asymmetrically clipped optical OFDM as the modulation scheme. Results are presented for both zero forcing and minimum mean square error equalizers. It is shown that the BER varies with the receiver position, with higher values in the center and the corners of the room.
The increasing use of white LEDs for indoor illumination provides a significant opportunity for Visible Light Positioning (VLP). The challenge is to design a small, unobtrusive sensor that can be incorporated into mobile devices to provide accurate measurements for triangulation. We present experimental results for a novel angle of arrival (AOA) detector that has been designed for use in a VLP system. The detector is composed of a transparent aperture in an opaque screen that is located above a quadrant photodiode (PD), separated by a known vertical distance. Light passing through the aperture from an LED casts a light spot onto the quadrant PD. The position of this spot, coupled with knowledge of the height of the aperture above the quadrant PD, provides sufficient information to determine both the incident and polar angles of the light. Experiments, using a prototype detector, show that detector is capable of accurate estimation of AOA. The root mean square errors (rMSE) were less than 0.11° for all the measured positions on the test bed, with 90% of positions having an rMSE of less than 0.07°.
Visible Light Communication (VLC) is an emerging technology that utilizes light-emitting diodes (LEDs) for both indoor illumination and wireless communications. It has the potential to enhance the existing WiFi network and connect a large number of high-speed internet users in future smart home environments. Over the past two decades, VLC techniques have made significant strides, resulting in transmission data rates increasing from just a few Mbps to several tens of Gbps. These achievements can be attributed to the development of various transceiver technologies. At the transmitter, LEDs should provide high-quality light for illumination and support wide modulation bandwidths. Meanwhile, at the receiver, optics systems should have functions such as optical filtering, light concentration, and, ideally, a wide field of view (FOV). The photodetector must efficiently convert the optical signal into an electrical signal. Different VLC systems typically consider various transceiver designs. In this paper, we provide a survey of some important emerging technologies used to create advanced optical transceivers in VLC.
Visible light positioning (VLP), using LED luminaires as beacons, is a promising solution to the growing demand for accurate indoor positioning. In this paper, we introduce a two-stage receiver that has been specifically designed for VLP. This receiver exploits the advantages of two different VLP receiver types: photodiodes and imaging sensors. In this new receiver design a quadrant angular diversity aperture (QADA) receiver is combined with an off-the-shelf camera to form a robust new receiver called QADA-plus. Results are presented for QADA that show the impact of noise and luminaire geometry on angle of arrival estimation accuracy and positioning accuracy. Detailed discussions highlight other potential sources of error for the QADA receiver and explain how the two-stage QADA-plus can overcome these issues.
16 December 2016 in Journal of Lightwave Technology
Aperture-based receivers are a new form of receiver for multiple-input multiple-output (MIMO) intensity-modulated direct-detection visible light communication (VLC). These receivers provide a wide field of view and excellent angular diversity using a compact planar structure and so are ideally suited for integration in hand-held devices such as smartphones. It is shown that in typical scenarios to achieve similar performance the photodiodes in a conventional receiver based on spatial diversity would have to be separated by distances greater than 30 cm. An in-depth analysis of the performance of aperture-based receivers is presented. Expressions are derived for the channel gain between an optical transmitter and each receiving element (RE) as a function of the transmission pattern of the transmitter, the design of the RE, and the relative positions of the transmitter and receiver. It is shown that a well-designed receiver consisting of multiple REs can separate signals received from different directions with low-multistream interference and that the associated MIMO channel matrices are well conditioned. Simulations are performed for a typical indoor VLC scenario in which light-emitting diode luminaires transmit information using asymmetrically clipped optical orthogonal frequency division multiplexing. Results are presented for receivers using both linear and nonlinear equalizers and for both line of sight (LOS) and LOS plus diffuse reception. The diffuse component is shown to improve the bit error rate (BER) performance slightly. It is shown that the BER depends on the receiver position. When a zero-forcing (ZF) linear receiver is used, the BER is dominated by the most attenuated signal, so the performance degrades at the corners of the room. In contrast, the receivers with nonlinear equalizers based on ZF followed by successive interference cancelation achieve low BER throughout the scenario.
Polynomial-cancellation-coded orthogonal frequency division multiplexing (PCC-OFDM) is a form of OFDM that has waveforms which are very well localized in both the time and frequency domains and so it is ideally suited for use in the 5G network. This paper analyzes the performance of PCC-OFDM in the uplink of a multiuser system using orthogonal frequency division multiple access (OFDMA) and compares it with conventional cyclic prefix OFDM (CP-OFDM), and universal filtered multicarrier (UFMC). PCC-OFDM is shown to be very much less sensitive to time and frequency offsets than either CP-OFDM or UFMC. For a given constellation size, PCC-OFDM in additive white Gaussian noise (AWGN) requires 3 dB lower signal-to-noise ratio (SNR) for a given bit-error-rate, and the SNR advantage of PCC-OFDM increases rapidly when there are timing and/or frequency offsets. For PCC-OFDM no frequency guard-band is required between different OFDMA users. PCC-OFDM is completely compatible with CP-OFDM and adds negligible complexity and latency, because it uses a simple mapping of data onto pairs of subcarriers at the transmitter, and a simple weighting-and-adding of pairs of subcarriers at the receiver. The weighting-and-adding step, which has been omitted in some of the literature, is shown to contribute substantially to the SNR advantage of PCC-OFDM. A disadvantage of PCC-OFDM (without overlapping) is the potential reduction in spectral efficiency because subcarriers are modulated in pairs, but this reduction is more than regained because no guard band is required and because, for a given channel, larger constellations can be used.