A study of the influence of temperature fluctuations of individual blocks of a fiber femtosecond frequency comb (FFC) generator and of the entire system as a whole on its output radio frequencies has been carried out. A two-circuit system for thermal stabilization of the air inside the FFC housing was implemented. An additional system for thermal stabilization of the transport fiber, which is included in the measurement scheme (outside the FFC), was implemented. A significant temperature effect on the measured output frequencies of the FFS is shown. Thanks to all the thermal stabilization systems, it has been shown that the instability of the developed fiber FFC introduced into its output microwave frequencies (in addition to the instability of the reference optical standard) is no worse than 2 × 10−16 per 1000 s.
An erbium fiber-based femtosecond optical frequency comb stabilized to an Yb + single-ion optical frequency standard was created. For the first time, a combination of an extra-cavity acousto-optic frequency modulator with fiber outputs and an intracavity electro-optic phase modulator based on a KTP crystal were used to stabilize offset frequency and one of the optical components of the Er:fiber femtosecond comb. As a result a locking bandwidth of 30 kHz for the optical comb offset frequency has been obtained. It is shown that the relative instability introduced by the stabilization and measurement systems into the output radio frequencies (in addition to the instability of the reference optical signal) is no worse than 5 × 10 −14 for averaging times of 1 s and 2 × 10 −16 for averaging times of 400 s.
We demonstrate the feasibility of triggering stationary high-energy pulse generation in Er-doped fiber lasers at ~1.5 µm via quasi-synchronous gain modulation. This simple method relies upon the sine-wave modulation of pump power at a frequency slightly surpassing the intrinsic frequency spacing of longitudinal modes in the laser cavity. This was previously implemented only in Yb-doped fiber lasers at ~1.1 µm. Here, for the first time, we experimentally validate the pulse shaping capabilities of this method also in Er fiber lasers, which, unlike Yb fiber lasers, have a three-level laser energy diagram (when pumped at 0.98 µm) with a very long-lived (10 ms) upper laser level. The feasibility of the method was validated both for normal and anomalous intracavity dispersion, which was not available in previous implementations in Yb fiber lasers at ~1.1 µm. Thus, the stable generation of a regular train of discrete nanosecond pulses with an energy of up to 180 nJ was achieved in our test-bed Er fiber laser upon the quasi-synchronous sine-wave modulation of the pump power at 0.98 µm. The results of our study testify to the general applicability of this affordable and reliable method for high-energy pulse generation in various rare-earth-doped fiber lasers.
We demonstrate the experimental realization of a dome-spectrum apodized chirped fiber Bragg gratings (ACFBGs) inscribed by femtosecond point-by-point technology in a polarization-maintaining (PM) fiber. ACFBGs fabrication method combines two techniques: a fiber translation velocity change-assisted inscription for chirped fiber Bragg gratings (CFBGs) and an energy modulation-based inscription for apodized fiber Bragg gratings (AFBGs). For both CFBG and AFBG writing techniques, inscription parameters (pulse energy, grating length, spectral bandwidth and apodization function) were optimized in SMF-28 fiber. Such a CFBG with 2 nm spectral bandwidth provides a group delay of 0.98 ns, which is equivalent to the dispersion compensation of a 30 km fiber section, thereby mitigating dispersion-induced temporal broadening of pulses. Gaussian apodization function provides a high side lobe suppression ratio (SLSR) of 22 dB for AFBG with a peak reflectivity of 90%. Thus, this optimization of parameters allowed us to fabricate and implement a combined ACFBG with a spectral bandwidth of 1 nm and SLSR of 18 dB in a PM fiber. The implementation of dome-spectrum ACFBGs in a mode-locked fiber laser as both a dispersion component and a spectral filter resulted in enhanced pulse energy and improved performance stability.