Larissa Krambeck

Dr. Larissa Krambeck

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 April 2024 in Experimental and Computational Multiphase Flow
Verified
Journal Article
Closed access
PDF file
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MMMarcia B. H. Mantelli
Marcia B. H. Mantelli

8 June 2023 in Heat and Mass Transfer
Verified
Journal Article
Closed access
PDF file
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
JMJuan Pablo Floréz Mera
Juan Pablo Floréz Mera
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli

31 May 2014 in International Review of Mechanical Engineering (IREME)
Verified
Journal Article
Closed access
PSPaulo Henrique Dias dos Santos
Paulo Henrique Dias dos Santos
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
DSDiogo Luiz Figueiredo dos Santos
Diogo Luiz Figueiredo dos Santos
TAThiago Antonini Alves
Thiago Antonini Alves
The thermal performance of a stainless steel heat pipe was analyzed based on its operation limits. The heat pipe developed here shall be used in compacts heat exchangers which can be used for instance in cogeneration plants. First, a mathematical model based on the heat pipe operation limits (capillary, viscous, sonic, entrainment and boiling limits) are presented. This model is used as an useful tool for design of heat pipes. Next, a heat pipe was produced with a stainless steel tube with an outer diameter of 6 mm, length of 230 mm and capillary structure composed by one round stainless steel screen mesh (number 100). The working fluid used was deionized water. The heat pipe has an evaporator and a condenser length of 80 mm and 110 mm, respectively. The condenser was cooled by forced convection using a water heat sink set at 20 °C and the evaporator was heated using an electrical resistor. This heat pipe was tested for increasing heat loads varying from 5 to 20 W. The theoretical and experimental results are compared in order to validate the mathematical model. Copyright © 2014 Praise Worthy Prize - All rights reserved.

5 June 2025 in Applied Thermal Engineering
Verified
Journal Article
Closed access
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli

1 January 2020 in Thermal Science
Verified
Journal Article
Open access
PDF file
NBNishida Felipe Baptista
Nishida Felipe Baptista
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
DDDos Santos Paulo Henrique Dias
Dos Santos Paulo Henrique Dias
TAThiago Antonini Alves
Thiago Antonini Alves
This work presents the use of electrical discharge machining (EDM) technology for manufacturing of three different types of axial microgrooves in heat pipes. This specific process, called wire electrical discharge machining (or wire-EDM), allows the fabrication of microgrooves on the inner wall of a heat pipe with accuracy. Different from other capillary structures, such as composite wick and screen mesh, the material is removed from the pipe’s container in order to conceive the capillary structure, which contributes with the mass reduction of the passive two-phase heat transfer device. The heat pipes were manufactured from a straight copper pipe with the external diameter of 9.45 mm, the inner diameter of 6.20 mm and a total length of 200 mm. Three types of axial microgrooves were manufactured for constant width (35 μm) and varying the depth (from 30 up to 48 μm) and thickness (from 35 up to 70 μm). The number of microgrooves was also varied from 21 up to 32 microgrooves. Water was used as the working fluid and the loading filling ratio was 60% of the evaporator volume. The condenser was cooled by air forced convection, the adiabatic section was insulated and the evaporator was heated by an electrical resistor and it was insulated from the environment with aeronautic thermal insulation. The thermal performance of the heat pipes are analyzed based on experimental results, so the heat pipes were tested at the horizontal and different inclinations under different low heat loads (from 5 up to 50 W or a heat flux from 0.21 up to 2.10 W/cm2). The experimental results showed that the axial microgrooves manufactured by the wire-EDM process worked satisfactorily in all analyzed cases and microgrooves of Type #1 showed a better thermal performance when compared with the others.

11 July 2018
Verified
Book Chapter
Open access
PDF file
TAThiago Antonini Alves
Thiago Antonini Alves
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
PSPaulo H. Dias dos Santos
Paulo H. Dias dos Santos
The heat pipe and thermosyphon are passive heat transfer devices with phase change, which can be applied for thermal management of thermoelectric cooling, such as the TEC hot side. The heat pipes basically consist of a metal tube sealed with capillary structure internally that is embedded with a working fluid. This capillary structure can be made of screen meshes, grooves, or sintered media. The thermosyphon is a heat pipe assisted by gravity, because it has no capillary structure. Then, in this chapter, manufacturing of low cost and easy-to-manufacture heat pipes and thermosyphon is described in detail, and an experimental evaluation of their thermal performance is accomplished. The considered devices were a rod, a thermosyphon, a mesh heat pipe, a grooved heat pipe, and a sintered heat pipe. According to the behavior of the global thermal resistance and the effective thermal conductivity, the passive devices operated satisfactorily with the exception of the rod and the thermosyphon in the horizontal position. The heat pipes were the best among the tested devices and the best position was vertical.