Kelvin Guessi Domiciano

Mr. Kelvin Guessi Domiciano

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 June 2023 in Heat and Mass Transfer
Verified
Journal Article
Closed access
PDF file
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
JMJuan Pablo Floréz Mera
Juan Pablo Floréz Mera
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli

5 June 2025 in Applied Thermal Engineering
Verified
Journal Article
Closed access
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli

1 April 2024 in Journal of Thermophysics and Heat Transfer
Verified
Journal Article
Closed access
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli
LALuis Alonso Betancur Arboleda
Luis Alonso Betancur Arboleda
Two flat plate diffusion-bonded pulsating heat pipes (PHPs) for the thermal management and heat dissipation of concentrated heat flux in electronics applications, such as aboard satellites and spacecraft, were specially developed for future tests aboard a sounding rocket in microgravity conditions. Both devices contain 26 channels with round cross sections, one with ultrasharp lateral grooves in the evaporator. Two heat sinks were tested: a water-cooling bath for the thermal characterization of the PHPs, and a copper box with a phase change material (dodecahydrate bibasic sodium phosphate) to be qualified as the heat storage for future microgravity tests. Water was used as the working fluid. The best filling ratio (relative to the total internal volume of the PHPs) was experimentally determined to be 50%, for which the devices presented the earliest startup and the lowest thermal resistance, around 0.033°C/W for the grooved PHP. This research proposes an efficient and alternative cooling method, the phase change material storage, to be used as a heat sink in future microgravity tests. Also, the microgravity effect on the thermal performance of such PHPs can be assessed by comparing the present results with future microgravity data obtained in an experimental module aboard a sounding rocket.

1 January 2025 in Materials Research
Verified
Journal Article
Open access
PDF file
LMLarissa Perego Mendes
Larissa Perego Mendes
MAMaria Cristina Amaral
Maria Cristina Amaral
LCLucas de Andrade Caldas
Lucas de Andrade Caldas
BMBianca Müller Martins
Bianca Müller Martins
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli
Flat heat pipes are highly effective for electronic thermal management, combining compact design with efficient heat transfer. Diffusion bonding is a promising manufacturing method, enabling leak-tight joints without notable plastic deformation. This study examined the effects of bonding temperature and pressure on the quality of miniature copper heat pipe joints. Optical microscopy, microhardness tests, and shear strength evaluations were used for assessment. Optimal results occurred at 875°C and 7MPa. Among four temperatures and three pressures tested, 900°C and 9MPa also yielded strong joints. Bonding time was fixed at 3600s. Good joints showed shear strengths of 5.92–6.17MPa and microhardness of 45–49HV. Interfaces had small, rounded, well-distributed defects that did not impair integrity. Temperature had a greater impact than pressure on joint quality. A flat miniature loop heat pipe made under optimal conditions (875°C, 7MPa, 3600s) displayed high-quality, deformation-free bonding and transferred up to 8W before reaching its operational limit—suitable for electronics.

21 December 2025 in Energies
Verified
Journal Article
Open access
PDF file
Larissa KrambeckLarissa Krambeck
Larissa Krambeck
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MBMaria Eduarda Beé
Maria Eduarda Beé
Marco MarengoMarco Marengo
Marco Marengo
MMMarcia Barbosa Henriques Mantelli
Marcia Barbosa Henriques Mantelli
Copper is widely used in two-phase devices for electronic cooling due to its ease of manufacture and high thermal conductivity. However, such high-heat conduction can limit the performance of pulsating heat pipes (PHPs) through transverse heat leakage. The use of lower-conductivity materials such as stainless steel enhances phase-change heat transfer by promoting stronger flow oscillations and reducing parasitic heat leakage, but it may be overall detrimental due to its poor thermal linkage between evaporator and condenser sections. Therefore, in this study, two main objectives are addressed: (i) experimentally characterizing the thermal behavior of a mini flat-plate PHP made of stainless steel (AISI 316L), and (ii) benchmarking its performance against a copper counterpart. Both devices were manufactured by diffusion bonding and tested under different orientations to evaluate operational robustness. The stainless steel PHP initiated oscillations at lower heat loads and showed larger temperature oscillations compared to the copper PHP, demonstrating effective phase-change heat transfer despite its lower thermal conductivity. A filling ratio of 71% of water provided the most stable operation, while orientation affected startup conditions and oscillation amplitude. Overall, stainless steel achieved comparable thermal performance to copper at low-to-moderate heat loads from 2.6 to 13.0 W/cm2, with additional benefits including reduced mass (~11% lighter), higher mechanical strength, and corrosion resistance. These results indicate that stainless steel is a viable alternative to copper at least for miniature flat-plate PHPs, offering a balance between thermal efficiency, mechanical robustness, and operational reliability.

11 March 2025 in International Journal of Thermofluids
Verified
Journal Article
Open access
KDKelvin Guessi Domiciano
Kelvin Guessi Domiciano
MMM. B. H. Mantelli
M. B. H. Mantelli
MMM. Mameli
M. Mameli
SFS. Filippeschi
S. Filippeschi