Shahin Mehraban

Dr. Shahin Mehraban

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 October 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
MBMatthew Burton
Matthew Burton
SMShahin Mehraban
Shahin Mehraban
JMJames McGettrick
James McGettrick
Trystan M. WatsonTrystan M. Watson
Trystan M. Watson
NLNicholas Lavery
Nicholas Lavery
MCMatthew Carnie
Matthew Carnie
Bulk non-toxic and Earth abundant Cu2−xS is pseudo-3D printed in a low-cost method yielding ZT values of up to 0.63.

9 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
LZLintao Zhang
Lintao Zhang
WHWilliam Harrison
William Harrison
SMShahin Mehraban
Shahin Mehraban
SBSteve Brown
Steve Brown
NLNicholas Lavery
Nicholas Lavery
This work investigated the feasibility of using a miniaturised non-standard tensile specimen to predict the post-necking behaviour of the materials manufactured via a rapid alloy prototyping (RAP) approach. The experimental work focused on the determination of the Lankford coefficients (r-value) of dual-phase 800 (DP800) steel and the digital image correlation (DIC) for some cases, which were used to help calibrate the damage model parameters of DP800 steel. The three-dimensional numerical simulations focused on the influence of the size effect (aspect ratio, AR) on the post-necking behaviour, such as the strain/stress/triaxiality evolutions, fracture angles, and necking mode transitions. The modelling showed that although a good correlation can be found between the predicted and experimentally observed ultimate tensile strength (UTS) and total elongation. The standard tensile specimen with a gauge length of 80 mm exhibited a fracture angle of ∼55°, whereas the smaller miniaturised non-standard specimens with low ARs exhibited fractures perpendicular to the loading direction. This shows that care must be taken when comparing the post-necking behaviour of small-scale tensile tests, such as those completed as a part of a RAP approach, to the post-necking behaviours of standard full-size test specimens. However, the modelling work showed that this behaviour is well represented, demonstrating a transition between the fracture angles of the samples between 2.5 and 5. This provides more confidence in understanding the post-necking behaviour of small-scale tensile tests.

22 June 2018 in Entropy
Verified
Journal Article
Open access
PDF file
SRSephira Riva
Sephira Riva
SMShahin Mehraban
Shahin Mehraban
NLNicholas Lavery
Nicholas Lavery
SSStefan Schwarzmüller
Stefan Schwarzmüller
Oliver OecklerOliver Oeckler
Oliver Oeckler
KYKirill Yusenko
Kirill Yusenko
We investigate the effect of alloying with scandium on microstructure, high-temperature phase stability, electron transport, and mechanical properties of the Al2CoCrFeNi, Al0.5CoCrCuFeNi, and AlCoCrCu0.5FeNi high-entropy alloys. Out of the three model alloys, Al2CoCrFeNi adopts a disordered CsCl structure type. Both of the six-component alloys contain a mixture of body-centered cubic (bcc) and face centered cubic (fcc) phases. The comparison between in situ high-temperature powder diffraction data and ex situ data from heat-treated samples highlights the presence of a reversible bcc to fcc transition. The precipitation of a MgZn2-type intermetallic phase along grain boundaries following scandium addition affects all systems differently, but especially enhances the properties of Al2CoCrFeNi. It causes grain refinement; hardness and electrical conductivity increases (up to 20% and 14% respectively) and affects the CsCl-type → fcc equilibrium by moving the transformation to sensibly higher temperatures. The maximum dimensionless thermoelectric figure of merit (ZT) of 0.014 is reached for Al2CoCrFeNi alloyed with 0.3 wt.% Sc at 650 °C.

21 April 2024 in Journal of Nuclear Materials
Verified
Journal Article
Open access
JHJack Haley
Jack Haley
SJStephen Jones
Stephen Jones
SMShahin Mehraban
Shahin Mehraban
NLNicholas Lavery
Nicholas Lavery
JCJonathan Cullen
Jonathan Cullen
DBDavid Bowden
David Bowden

1 November 2018 in Journal of Non-Crystalline Solids
Verified
Journal Article
Open access
UDU. Dahlborg
U. Dahlborg
JGJ.-G. Gasser
J.-G. Gasser
GCGabriel J CUELLO
Gabriel J CUELLO
SMShahin Mehraban
Shahin Mehraban
NLNicholas Lavery
Nicholas Lavery
MCMonique Calvo-Dahlborg
Monique Calvo-Dahlborg

19 December 2025 in Journal of Nuclear Engineering
Verified
Journal Article
Open access
PDF file
DBDavid Bowden
David Bowden
BEBenjamin Evans
Benjamin Evans
JHJack Haley
Jack Haley
JJJim Johnson
Jim Johnson
ACAlexander Carruthers
Alexander Carruthers
PBPete Barnard
Pete Barnard
Future fusion power plants require structural materials that can withstand extreme operating conditions, including high coolant outlet temperatures, mechanical loading, and radiation damage. Reduced-activation ferritic martensitic (RAFM) steels are a primary candidate as a structural material for such applications. This study demonstrates the successful production of a 5.5-tonne RAFM billet via electric arc furnace (EAF) technology, enabling scalable, cost-effective manufacturing. The resulting UK-RAFM alloy offers superior tensile strength and creep lifetime performance compared to Eurofer97. This is attributed to alterations in the initial forging process during manufacture. Modified thermomechanical treatments (TMTs) were subsequently applied to the UK-RAFM, which are shown to enhance the tensile strength further, particularly at 650 °C. Building on this, an Advanced RAFM (ARAFM) steel was designed to exploit the benefits of optimised chemistry to encourage metal carbonitride (MX) precipitate evolution alongside bespoke TMTs. Challenges around ensuring suitable processing windows in these steels, to avoid the over-coarsening of MX precipitates or the formation of deleterious delta-ferrite, are discussed. A subsequent 5.5-tonne ARAFM billet has since been produced using EAF facilities, with performance to be reported separately. This work highlights the synergy between alloy design, process optimisation, and industrial scalability, paving the way for a new generation of low-cost, high-volume, fusion-grade steels.