The failure modes, ultimate load, stiffness performance, and their influencing factors of a composite sandwich laminated box beam under three-point bending load are studied by an experiment, finite element model, and analytical method. The three-point bending experiment was carried out on three different core composite sandwich laminated box beams, and the failure modes and bearing capacity were studied. With the use of composite progressive damage analysis and the core elastoplastic constitutive model, the finite element model of the composite sandwich laminated box beam was established, and the three-point bending failure process and failure modes were analyzed. The analytical model was established based on the Timoshenko beam theory. The overall bending stiffness and shear stiffness of the composite sandwich laminated box beam were calculated by the internal force–displacement relationship. The results show that the composite sandwich laminated box beam mainly suffers from local crushing failure, and the errors between the finite element simulation and the experiment result were within 7%. The analytical model of the composite sandwich laminated box beam can approximately predict the overall stiffness parameters, while the maximum error between theoretic results and experimental values was 5.2%. For composite aluminum honeycomb sandwich laminated box beams with a ratio of span to height less than 10, the additional deflection caused by shear deformation has an error of more than 25%. With the ratio of circumferential layers to longitudinal layers increasing, the three-point bending ultimate load of the composite sandwich laminated box beam increases, but the ratio of the overall stiffness to mass reduces. The use of low-density aluminum foam and smaller-wall-thickness cell aluminum honeycombs allows for the more obvious benefits of light weight.
The development of lightweight, impact‐resistant, and high energy‐consuming materials is of great significance for improving the defense capabilities of military equipment. As a new type of damping material, metal rubber has demonstrated great potential for application in the field of impact protection. In this paper, the dynamic mechanical response of metal rubber under a high strain rate is studied, which provides a new idea for developing high‐performance protective materials. The stress‐strain curves, energy absorption performance, and wave transmission performance of metal rubber at various strain rates were investigated based on a split‐Hopkinson pressure bar (SHPB) device. The dynamic stress‐strain curve of metal rubber is divided into three stages: elastic stage, plastic stage, and failure stage. The optimal energy absorption efficiency is greater than 0.5, and the maximum value can reach 0.9. The wave transmittance is less than 0.01. The dynamic mechanical tests have proved that metal rubber has excellent energy absorption capacity and impact resistance property. A constitutive model based on Sherwood–Frost was established to predict the dynamic mechanical behavior of metal rubber. The results of comparison between the calculation and the experiment show that the constitutive model can accurately predict the dynamic mechanical performance of metal rubber.
Four composite structures (SiC/UHMWPE/TC4, SiC/TC4/UHMWPE, SiC/UHMWPE/MR/TC4, and SiC/TC4/MR/UHMWPE) were prepared using silicon carbide (SiC) ceramics, ultrahigh molecular weight polyethylene (UHMWPE), titanium alloy (TC4), and metal rubber (MR). The transmitted waves, failure forms, stress wave propagations, and energy dissipations of the composite structures were studied through Split Hopkinson Pressure Bar (SHPB) tests and numerical simulations. The results show that MR in composite structures can delay, attenuate, and smooth the stress wave, thereby reducing SiC damage. UHMWPE on the back of SiC provides cushioning for SiC, while TC4 on the back of SiC aggravates the damage of SiC. The composite structures with MR mainly dissipate the impact energy by reflecting energy, and the energy dissipation performance is better than that of composite structures without MR. A comprehensive comparison of transmitted waves, damage forms, stress wave propagations, and energy dissipations of the four composite structures shows that SiC/UHMWPE/MR/TC4 structure has the best impact resistance. Increasing the thickness of MR in the composite structures can improve the impact resistance, but there are also stress concentration and interface tensile stress.
Acoustic localization for a moving source plays a key role in engineering applications, such as wildlife conservation and health protection. Acoustic detection methods provide an alternative to traditional radar and infrared detection methods. Here, an acoustic locating method of array signal processing based on intersecting azimuth lines of two arrays is introduced. The locating algorithm and the precision simulation of a single array shows that such a single array has good azimuth precision and bad range estimation. Once another array of the same type is added, the moving acoustic source can be located precisely by intersecting azimuth lines. A low-speed vehicle is used as the simulated moving source for the locating experiments. The length selection of short correlation and moving path compensation are studied in the experiments. All results show that the proposed novel method locates the moving sound source with high precision (<5%), while requiring fewer instruments than current methods.
The development of protective materials and structures is of great significance for improving the impact resistance, penetration resistance and spalling resistance of military equipment. At present, the layered composite structure has been widely used due to its good protective performance. In this paper, a special elastic porous material-metal rubber (MR) with excellent cushioning and damping properties was used to prepare high-performance layered composite structures. To begin with, the dynamic mechanical response and the dynamic cumulative damage effect of MR were studied through Split-Hopkinson Pressure Bar (SHPB) tests. Then, the failure form and stress wave propagation characteristics of the layered composite structures were investigated through SHPB tests and finite element method. The results show that repeated impacts can enhance the compactness of MR, thereby increasing the ultimate bearing capacity and energy absorption capacity, which is beneficial for MR to resist repeated impacts. The MR in composite structures can reduce ceramic damage, attenuate stress wave and smooth stress distribution. The titanium alloy on the back of the ceramic will aggravate the damage of the ceramic, and ultra-high molecular weight polyethylene on the back of the ceramic provides cushioning for the ceramic. Therefore, the impact resistance of the composite structure can be improved by adding MR and the reasonable arrangement of materials, and the SiC/UHMWPE/MR/TC4 composite structure has relatively reasonable stress distribution and better protection performance.