Lutuf Ertürk

Dr. Lutuf Ertürk

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2025 in The European Physical Journal Plus
Verified
Journal Article
Open access
PDF file
NDNetice Duman
Netice Duman
HAHalil İbRahim Acar
Halil İbRahim Acar
LELutuf Ertürk
Lutuf Ertürk
With the increase in energy consumption, resources are decreasing while costs are rising. The Covid-19 pandemic and wars in some countries have also led to increased costs. Considering the environmental damage, the search for new energy sources and the demand for existing renewable energy sources have increased. Among renewable energy sources, wind energy is one of the most prominent energy sources due to its environmental friendliness. In recent years, studies on wind characteristics and wind energy distribution have been conducted in many parts of the world. But, it has not been conducted that a detailed study using different probability density functions specifically for Sivas province in Türkiye. This study investigated the wind energy potential for Sivas province using various probability density functions. Data from two nearby stations were used in the calculations. Despite the proximity of the stations, it was determined that the emerging wind trends showed some differences. For Station A, it is observed that probability density functions other than Rayleigh provide a better fit, especially at low wind speeds. However, deviations from actual values are observed at certain wind speeds. For Station B, functions other than Weibull show a better fit, although it can be said that the wind characteristics are more irregular in the winter season, and the predicted functions do not provide a better fit. Stations A and B exhibited different wind characteristics, except for the autumn season. It was observed that collecting data and analyzing wind power at the site where a wind farm will be established is quite important. As a result of the study, it was concluded that the potential wind powers at both stations were quite low and not very suitable for wind farm installation.

19 February 2024 in Uluslararası Muhendislik Arastirma ve Gelistirme Dergisi
Verified
Journal Article
Closed access
LELutuf Ertürk
Lutuf Ertürk
SKSakine Kıratlı
Sakine Kıratlı
Dünya nüfusunun sürekli artması, doğal kaynakların tükenmesine hatta zamanla yok olmasına, atık malzemelerin ise artmasına neden olmaktadır. Atık malzemelerin değerlendirilmesi, hem doğada sınırlı miktarda bulunan kaynakların tüketimini azaltmakta hem de atık malzemelerin çevrede oluşturduğu problemleri en aza indirmektedir. Literatürde, kompozit malzemelerde katkı olarak atık malzemelerin kullanımına yönelik birçok çalışma bildirilmiştir. Tarımsal atıklar, hayvansal atıklar ve tekstil atıkları gibi birçok atık malzemenin kompozit malzemelerde kullanıldığı görülmüştür. Yapılan çalışmalarda atık malzemelerin kompozit malzemelerde kullanılmasının çekme, eğilme, kırılma mukavemeti gibi mekanik özellikler açısından birçok avantaj sağladığı sonucuna varılmıştır.

2 September 2025 in Revista de Metalurgia
Verified
Journal Article
Open access
PDF file
LELutuf Ertürk
Lutuf Ertürk
BSBurhan Selçuk
Burhan Selçuk
Boriding is usually performed separately after sintering in powder metallurgy methods. In the borosintering process, sintering and boriding processes are carried out simultaneously. This saves energy as it shortens the heat treatment time. Additionally, since the heat treatment are shorter in time, it prevents problems that may occur in the materials subjected to this heat treatment. Thanks to the borosintering, boriding is also done on parts produced with powder metallurgy without the need for any extra processing. In this work, iron-based samples were made using powder metallurgy routes. And then, sintering and boronizing processes were applied individually to some samples and simultaneously to others (borosintering). Boriding processes were conducted in solid media (20% B4C, 5% NaF, 75% SiC). Boriding, sintering and borosintering processes were conducted at 950, 1000, and 1050 °C for four hours. SEM was used to investigate the morphology of the produced boride layers, EDX was used to examine the elemental composition, and XRD was used to examine the phases. It is observed that when the temperature rises, the layer thickness increases. It was discovered that the sintered samples were mostly Fe, while the boronized samples were predominantly Fe2B. The microhardness of the boride layers was measured. Additionally, the samples were then subjected to sliding and abrasive wear tests. The hardness values of the boride layer made at 1000 °C and 1050 °C were higher than those at 950 °C. Borosintered samples have been found to be resistant to both sliding and abrasive wear. Borosintered samples, as well as sintered and borided samples, demonstrated similar characteristics. Regarding the process steps and costs, it was determined that the borosintering technique would provide an enormous benefit.

25 December 2024 in International Journal of Energy Studies
Verified
Journal Article
Open access
PDF file
NDNetice Duman
Netice Duman
HAHalil İbRahim Acar
Halil İbRahim Acar
LELutuf Ertürk
Lutuf Ertürk
Thermoacoustic refrigerator (TAR) is one of the best technologies accepted as an alternative to traditional cooling systems. Factors such as the fact that TAR systems have minimum environmental and human health problems such as global warming and ozone layer depletion, being lightweight and having no moving parts make these systems seen as promising clean technologies in the future. TAR creates a cooling effect by converting acoustic energy into thermal energy. In this research, a quarter wave standing wave thermoacoustic refrigerator using air as the working fluid and a speaker as an acoustic power source was designed and simulated. An algorithm suitable for the literature on thermoacoustics was used in the design. Simplified linear theory was used in this algorithm and the designed standing wave TAR model was simulated with the Design Environment for Low Amplitude Thermo Acoustic Energy Conversion (DeltaEC) program. In the study, the changes of various parameters along the resonator length were examined and the results were given graphically. Design and simulation cooling coefficient of performance (COP) results were 2.236 and 1.036 respectively.

30 September 2025 in Cumhuriyet Science Journal
Verified
Journal Article
Closed access
MBMehmet Bulut
Mehmet Bulut
LELutuf Ertürk
Lutuf Ertürk
Recycling industrial waste plays a crucial role in sustainable environmental balance. Therefore, it is essential to effectively coordinate recycling and waste management, recovering materials like paper, plastic, and metal that are unsuitable for disposal. The investigation of mechanical properties of polymer matrix composites reinforced with waste iron powder can reveal significant enhancements in mechanical properties. Therefore, this study experimentally examines the tensile and flexural mechanical properties of polymer matrix composites reinforced with waste iron metal powder. Morphology investigations were carried out on the fractured tensile and flexural test specimens and comments were made on the results. For this purpose, the effect of reusability of iron powder additive as filler material on mechanical properties at four different iron powder/epoxy weight ratios (0, 2%, 4%, and 8%) was investigated. Subsequently, epoxy/iron powder homogeneous polymer matrix composite blends were cast into metal molds and test specimens were obtained. The results showed that the addition of 4 wt. % iron powder increased the tensile strength by 28%; however, it was concluded that the addition of iron powder negatively affected the flexural strength and modulus with concluding that this decrease in flexural test results was the result of the decrease in the interfacial adhesion strength between iron powder/epoxy.

10 December 2024 in Acta Scientiarum. Technology
Verified
Journal Article
Open access
PDF file
LELutuf Ertürk
Lutuf Ertürk
BSBurhan Selçuk
Burhan Selçuk
In this study, samples prepared by pressing iron-based powder mixtures were divided into two different groups; sintering and boriding processes were applied in two steps in some of the samples, and in a single step in some of them. Sintering and boriding processes were applied at 950, 1000 and 1050°C for 2 hours. Various properties of borided and unborided samples in the first group and borosintered samples in the second group were compared. The microstructure in the samples was examined by optical microscope and SEM. Elemental analysis was performed by EDX. Phases formed as a result of boriding were detected by XRD. Surface roughness, microhardness measurements and wear tests were conducted on the samples. In the samples produced by powder metallurgy, the specifications of the structures formed as a result of first sintering and then boronizing process were similar. In both cases, the microhardness values of the material increased and wear-resistant structures were formed. It has been observed that the properties of the resulting structures show some changes depending on the temperature.