Abideng Hawa

Mr. Abideng Hawa


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 November 2014 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
WPWoraphot Prachasaree
Woraphot Prachasaree
SLSuchart Limkatanyu
Suchart Limkatanyu
AHAbideng Hawa
Abideng Hawa
ASAgarat Samakrattakit
Agarat Samakrattakit

1 January 2013 in The Scientific World Journal
Verified
Journal Article
Open access
PDF file
AHAbideng Hawa
Abideng Hawa
DTDanupon Tonnayopas
Danupon Tonnayopas
WPWoraphot Prachasaree
Woraphot Prachasaree
This study reports on the microstructure, compressive strength, and drying shrinkage of metakaolin (MK) based geopolymers produced by partially replacing MK by oil palm ash (OPA). The OPA was used as raw material producing different molar ratios of SiO2/Al2O3 and CaO/SiO2. The geopolymer samples were cured at 80°C for 1, 2, or 4 hours and kept at ambient temperature until testing. The compressive strength was measured after 2, 6, and 24 hours and 7 and 28 days. The testing results revealed that the geopolymer with 5% OPA (SiO2 : Al2O3 = 2.88 : 1) gave the highest compressive strength. Scanning electron microscopy (SEM) indicated that the 5% OPA sample had a dense‐compact matrix and less unreacted raw materials which contributed to the higher compressive strength. In the X‐ray diffraction (XRD) patterns, the change of the crystalline phase after heat curing for 4 hours was easily detectable compared to the samples subjected to a shorter period of heat curing.

1 January 2013 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
AHAbideng Hawa
Abideng Hawa
DTDanupon Tonnayopas
Danupon Tonnayopas
WPWoraphot Prachasaree
Woraphot Prachasaree
PTPichai Taneerananon
Pichai Taneerananon
High early strength is the most important property of pavement repair materials to allow quick reopening to traffic. With this in mind, we have experimentally investigated geopolymers using low cost raw materials available in Thailand. The geopolymer mortar was metakaolin (MK), mixed with parawood ash (PWA, rubberwood ash) or oil palm ash (OPA) as binder agent. Rubberwood is often used as raw material for biomass power plants in Thailand, especially at latex glove factories and seafood factories, and burning rubberwood generates PWA. Both PWA and OPA are therefore low cost residual waste, locally available in mass quantities. The geopolymer samples were characterized for compressive strength, drying shrinkage, and bond strength to Portland cement mortar with slant shear test. The experimental design varied the contents of PWA and OPA and the heat curing time (1, 2 and 4 h) after hot mixture process. The hot mixture process resulted in very high early strength. In addition, we achieved high compressive strengths, low drying shrinkage, and very significant bond strength enhancement by use of the ashes.

1 May 2023 in Civil Engineering Journal
Verified
Journal Article
Open access
PDF file
AHAbideng Hawa
Abideng Hawa
PSPreecha Salaemae
Preecha Salaemae
AAAkkadath Abdulmatin
Akkadath Abdulmatin
KOKrittiya Ongwuttiwat
Krittiya Ongwuttiwat
WPWoraphot Prachasearee
Woraphot Prachasearee
Most geopolymer binder is produced using raw materials comprising powder with high silica and alumina content. Additionally, fine aggregate is prepared with river sand for high bulk density. This research proposes using palm oil ash (POA) for the main binder and palm oil clinker (POC) for the fine aggregate. The chemical composition of POA has high levels of silica but low alumina, so it must undergo partial replacement with alumina powder (AP). POA and POC are waste by-products of electrical power plants. The properties to be investigated include compressive strength, bulk density, water absorption, and microstructure. The effect of mixture composition, i.e., POA and field Para rubber latex (FPRL), on those properties is of particular interest. POA was substituted by AP and FPRL at 2.5%, 5%, 7.5%, and 10%, and at 1%, 3%, 5%, and 10%, respectively. Geopolymer mortars were cured at ambient temperature for 24 hours and kept at ambient temperature until testing. The compressive strengths of the geopolymer mortars were tested at 1, 7, and 28 days. The results showed that the optimal mixture consisted of 5% AP in the case of AP only and 1% FPRL in the case of FPRL only, while the ternary optimal mixture of 1% FPRL and 7.5% AP achieved higher compressive strengths than the control (CT) sample at 28.16, 19.98, and 25.30 MPa, respectively, after 28 days of curing. Bulk density increased with the addition of AP and FPRL. The microstructures of the geopolymer samples investigated using SEM-EDX showed the presence of different elements with different mixtures and displayed a dense, compact geopolymer matrix with high compressive strength. Using large amounts of POA in combination with AP and FPRL improved the environmental aspects of landfill disposal. Doi: 10.28991/CEJ-2023-09-05-017 Full Text: PDF

28 October 2025 in Journal of Engineering and Technological Sciences
Verified
Journal Article
Open access
PDF file
AHAbideng Hawa
Abideng Hawa
PSPreecha Salaemae
Preecha Salaemae
This paper has analyzed the thermal insulation of geopolymer blocks prepared using palm oil ash (POA) with the addition of alumina powder (AP) and field Para rubber latex (FPRL). The block samples were set up to use 3 and 5 channels and channel width of 2 and 4 mm each with geopolymer binder as POA (containing 5% FPRL and 0%, 2.5%, 5%, 7.5%, and 10% AP) and POC as fine aggregate. The compressive strength, water absorption, bulk density of the geopolymer mortars and thermal conductivity of geopolymer blocks were explored. The AP and FPRL had minimal impact on the compressive strength of the geopolymer mortars and the greater the amount of AP the less water was absorbed. Thermal conductivity of 4 mm wide channel geopolymer blocks was lower than that of 2 mm wide channel blocks and 5 channels blocks had lower thermal conductivity in comparison to 3 channel blocks. The geopolymer blocks had low thermal conductivity relative to the commercial concrete blocks. This study offers valuable information to the application of geopolymers made of POA with FPRL and AP to produce geopolymer materials, POC as a fine aggregate to produce green building materials with enhanced thermal insulation.

24 March 2021 in Iranian Journal of Science and Technology, Transactions of Civil Engineering
Verified
Journal Article
Closed access
PDF file
WPWoraphot Prachasaree
Woraphot Prachasaree
TJThimaporn Jansri
Thimaporn Jansri
MSMongkol SaeJia
Mongkol SaeJia
AHAbideng Hawa
Abideng Hawa
SLSuchart Limkatanyu
Suchart Limkatanyu