Aeration is one of the most energy-intensive operations in wastewater treatment plants, with its efficiency strongly affected by the presence of surfactants. This study investigates the impact of Sodium Dodecyl Sulphate (SDS) on oxygen mass transfer using a commercial fine-bubble diffuser. Oxygen transfer experiments were performed under varying air flow rates and SDS concentrations. Key parameters, including the volumetric mass transfer coefficient (), gas holdup, bubble size, and interfacial area, were experimentally measured and analysed. SDS reduces the average bubble diameter by up to 50%; above 4 mg/L, further increases in concentration do not change the bubble size. Gas holdup increases by approximately 2% per mg L−1 of SDS, and a new empirical correlation was proposed to predict gas holdup as a function of air flow rate and surfactant concentration, achieving an R2 of 0.97 with deviations below 10%. Despite the increase in interfacial area, SDS strongly suppresses interfacial turbulence, reducing the liquid-side mass transfer coefficient () by up to 70%, which ultimately leads to a significant loss of overall oxygen transfer efficiency. The Sardeing model, originally developed for single bubbles, successfully predicted within ±15% of the experimental values, demonstrating its potential as a practical tool for estimating oxygen transfer in aeration systems. These findings highlight the substantial impact of surfactants on fine-bubble aeration performance and underscore the need to account for their effects in the design and operation of industrial aeration systems.
Fine-bubble aeration is a core process in wastewater treatment plants (WWTPs). However, the physical mechanisms linking bubble plume hydrodynamics to oxygen transfer performance remain insufficiently quantified under configurations representative of full-scale installations. This study presents a local multi-sensor experimental characterization of a multiple bubble plume system using a 4 × 4 array of commercial membrane diffusers in a pilot-scale aeration tank (2 m3), emulating WWTP diffuser density and geometry. Airflow rate was varied to analyze its effects on mixing and oxygen transfer efficiency. The experimental methodology combines three complementary measurement approaches. Oxygen transfer performance is quantified using a dissolved oxygen probe. Liquid-phase velocity fields are then mapped using Acoustic Doppler Velocimetry (ADV). Finally, local two-phase measurements are obtained using dual-tip Conductivity Probe (CP) arrays, which provide bubble size, bubble velocity, void fraction, and Interfacial Area Concentration (IAC). Based on these observations, a zonal hydrodynamic model is proposed to describe plume interaction, wall-driven recirculation, and the formation of a collective plume core at higher airflows. Quantitatively, the results reveal a 29% reduction in Standard Oxygen Transfer Efficiency (SOTE) between 10 and 40 m3/h, driven by a 41% increase in bubble size and an 18% rise in bubble velocity. Bubble chord length also increased with height, by 33%, 19%, and 15% over 0.8 m for 10, 20, and 40 m3/h, respectively. These trends indicate that increasing airflow enhances turbulent mixing but simultaneously enlarges bubbles and accelerates their ascent, thereby reducing residence time and negatively affecting oxygen transfer. Overall, the validated multiphase datasets and mechanistic insights demonstrate the dominant role of diffuser interaction in dense layouts, supporting improved parameterization and experimental benchmarking of fine-bubble aeration systems in WWTPs.
The expanded granular sludge bed (EGSB) reactor system is a mature anaerobic treatment technology that continues to evolve and expand its applications in wastewater management. This class of reactors provides high treatment efficiencies and significant biogas production rates due to the interaction among the three involved phases: the liquid water matrix, solid granules, and biogas. The present study examines the three-phase flow characteristics of such reactors, which operate under very specific conditions—namely, a reduced density difference between the liquid and millimeter-sized solid particles, relatively low gas hold-up, and moderate bed expansion. To ensure the reproducibility and generality of the results, the solid granules were replaced with acrylonitrile–butadiene–styrene (ABS) particles with a density of ρp = 1050 kg/m3 and two mean diameters, dp = 2.5 mm and dp = 4 mm. These solids were subjected to various combinations of superficial gas (jg) and liquid (jl) velocities in a co-current vertical column of 1 m length and 68 mm inner diameter. Two liquids with different densities, ρw = 1000 kg/m3 and ρw = 1025 kg/m3, were employed to enable a non-dimensional analysis of the results. Unlike previous studies, the results presented here allow for a comprehensive characterization of the flow regimes in terms of the interaction among the three phases under conditions of low density difference and millimeter-sized particles—conditions that lie outside the ranges typically investigated in gas–liquid–solid fluidized bed reactors.
Intrusive phase-detection probes remain a standard tool for local characterization of gas–liquid bubbly flows, but their accuracy is strongly affected by probe geometry and bubble–probe interaction kinematics. This work presents a Monte Carlo-based framework to evaluate four-sensor intrusive probes in bubbly flow, relaxing the classical assumptions of spherical bubbles and purely axial trajectories. Bubbles are represented as spheres or ellipsoids, a broad range of non-dimensional probe geometries are explored, and local quantities such as interfacial area concentration, bubble and flux velocities, and chord lengths are recovered from synthetic four-sensor signals. The purpose of the framework is threefold: (i) it treats four-sensor probes in a unified way for interfacial area, velocity, and chord length estimation; (ii) it includes ellipsoidal bubbles and statistically distributed incidence angles; and (iii) it yields compact correction laws and design maps expressed in terms of the spacing-to-diameter ratio , the dimensionless probe radius , and the missing ratio (defined as the fraction of bubbles that cross the probe footprint without being detected), which can be applied to different intrusive four-sensor probes. The numerical results show that, within a recommended geometric range and and for missing ratios , the axial velocity estimates the bubble centroid velocity and its projection with typical errors within , while a chord length correction recovers the underlying chord length distribution with a residual bias of only a few percent. The proposed interfacial area correction, written solely in terms of , remains accurate in polydisperse bubbly flows. Outside the recommended range, large probe radius or extreme tip spacing lead to velocity and chord length errors that can exceed 20–30%. Overall, the framework provides quantitative guidelines for designing and using four-sensor intrusive probes in bubbly flows and for interpreting their measurements through geometry-aware correction factors.
4 March 2026 in Nuclear Engineering and Technology
Aeration is one of the most energy-intensive operations in wastewater treatment plants, with its efficiency strongly affected by the presence of surfactants. This study investigates the impact of surfactants on oxygen mass transfer using a commercial fine bubble diffuser. Oxygen transfer experiments were performed under varying air flow rates and surfactant concentrations. Key parameters, including the volumetric mass transfer coefficient (kLa), gas holdup, bubble size, and interfacial area, were experimentally measured and analysed. Results show that kLa increases with air flow rate due to larger interfacial area, while the Standard Oxygen Transfer Efficiency (SOTE) decreases, particularly at higher surfactant concentrations. Surfactants promote smaller bubble sizes and higher gas holdup, thus increasing the interfacial area. However, they significantly reduce the liquid-side mass transfer coefficient (kL) by suppressing interfacial turbulence. Despite the increased interfacial area, the reduction in kL leads to lower overall oxygen transfer efficiency. These findings highlight the importance of accounting for surfactant effects in the design and operation of industrial aeration systems.