Ni (1 wt%)-, Pt (1 wt%)- and [Ni (0.5 wt%)/Pt (0.5 wt%)]-doped TiO₂ nanoporous catalysts have been successfully obtained through a facile two-step hydrothermal route. TiO₂ crystallizes mostly in the anatase phase and acts as a mesoporous matrix. Meanwhile, Ni, Pt and Ni/Pt dopants form small nanoparticles (NPs) (3–95 nm in diameter) which are hosted by the TiO₂ framework. The resulting composites exhibit a rather large surface area, in the range of 186–200 m2/g. The band gap energy reduces from 3.03 eV for the undoped TiO₂ to 2.15 eV for the Pt-loaded TiO₂. As a consequence, absorption expands toward the visible light range. The photodegradation of Rhodamine B dye in aqueous medium has been investigated under UV–vis light irradiation. The presence of Ni, Pt and Ni/Pt NPs significantly enhances the photocatalytic activity of the material. Furthermore, the Ni-doped TiO₂ shows ferromagnetic behavior at room temperature, which makes its recovery and subsequent fast reutilization possible. Interestingly, this sample also exhibits the best stability upon recycling. Considering all the current challenges in sustainable water remediation, these new photocatalysts could find applications in real environmental contexts in the near future
ZrO2-decorated ZnO (ZrO2|ZnO) nanoparticles (NPs) have been synthesized by a facile co-precipitation method in the presence of cetyltrimethylammonium bromide (CTAB) surfactant. The ZrO2 amount in the NPs has been varied from 1.0, 2.0, 4.9, to 9.3% by weight. The resulting NPs are heterostructured and consist of a crystalline ZnO core (wurtzite phase) surrounded by an amorphous ZrO2 layer. X-ray diffraction analyses support this observation. The NPs show a narrow size distribution and are slightly elongated. Compared to pure ZnO NPs, the hybrid ZrO2|ZnO ones show enhanced photocatalytic activity toward the degradation of Rhodamine B under UV–Vis light. Such enhancement has been partly attributed to the increased amount of oxygen vacancies when ZrO2 is incorporated into the NPs, as shown by X-ray photoelectron spectroscopy analyses.
A fully nanoporous Fe-rich alloy, prepared by selective dissolution of melt-spun Fe43.5Cu56.5 ribbons, exhibits outstanding properties as a heterogeneous Fenton catalyst toward the degradation of methyl orange (MO) in aqueous solution. In addition, the ferromagnetic characteristics of this material enable its wireless manipulation toward specific locations within polluted wastewater. The influence of selective dissolution on the microstructure, sample morphology (surface and cross-section), elemental composition, and magnetic properties of the resulting nanoporous alloy is investigated. The dealloying procedure enhances the saturation magnetization and drastically increases the catalytic performance (i.e., the time required for full degradation of MO from the medium is reduced by a factor of approximately 2 by subjecting the Fe43.5Cu56.5 ribbons to prior dealloying). Remarkably, the effectiveness of this nanoporous material surpasses the results obtained by the homogeneous Fenton reaction using an equivalent concentration of Fe cations leached into the media from the nanoporous alloy. The different factors that promote the high catalytic activity are discussed. The outstanding catalytic activity, together with the simplicity of the synthetic procedure, makes this material very appealing for water remediation using advanced Fenton processes.
The present work aims to evaluate the electrochemical behaviour of 316L stainless steel flat sheets both uncoated and coated with an organic–inorganic silane hybrid formulation based on TEOS (tetraethyl orthosilicate) and TMES (Trimethylethoxysilane) as silane precursors. The influence of the modification of the silane-based layer by the incorporation of 3-aminopropyl trimethoxysilane (APS) doped TiO2 (N-TiO2) on the pitting properties of the coatings has been studied. The obtained protective films have been characterized from compositional (EDX), morphological (FE-SEM), and electrochemical (corrosion) points of view. Concerning their morphology, the coatings look continuous and smooth. Regarding their electrochemical properties, the results show that the application of the developed N-TiO2-containing silane coatings extends the passive potential range of 316L stainless steel in simulated body fluid; thus, it improves the pitting resistance of the substrate.