Removal of particulate residues represents a very challenging step in current CMOS-technology nodes. The continued miniaturization and the introduction of novel materials in the semiconductor industry have resulted in very stringent requirements for device fabrication steps such as cleaning processes [. Physical forces, acting directly on the surface to be cleaned, are currently employed for delicate particle removal as an alternative to more aggressive chemistries [2]. High frequency ultrasounds (500 kHz 4 MHz), or megasonics, rely on the action of oscillating bubbles created during the ultrasonic agitation of the cleaning liquid. Strongly oscillating gas bubbles are able to generate shear forces, which are considered to be responsible for cleaning [3]. However, collapsing bubbles close to a surface can also produce water jets and shockwaves which lead to damage of fragile structures. Fundamental research is needed in order to overcome these issues by improving the understanding of the physical parameters playing a role in the acoustic cavitation of bubbles. This study reports the effects of lowering the surface tension of the liquid bulk on the bubble activity in the MHz range. A lower surface tension (45 mN/m) with respect to water (72 mN/m) is obtained by adding a non-ionic surface-active agent (TritonX-100). After fully characterizing its wettability, a cleaning solution containing surfactant is investigated under pulsed and continuous acoustic fields, for different acoustic amplitudes and gas concentrations. The aim is to increase bubble activity while reducing the strength of the bubble collapse. The results obtained can be useful in tuning megasonic cleaning systems towards more efficient processes.
Ge and III/V materials are investigated as high mobility channel materials for devices beyond the 14 nm technology node. Passivation of the interface is a prerequisite as dangling bond states trap charges and reduce the mobility. Passivation of the Ge/high-κ interface can be done by using GeO2 as a passivation layer. However, large thicknesses are needed to keep a low defect density. Introduction of S at the interface can solve this issue. Passivation of III/V materials is still a major problem. Oxidation of the III-As surface leads to stress at the surface creating As-As bonds. Oxides can be partially removed by wet treatment or during the ALD deposition. The defects related to As-As bonds cannot be removed by the ALD process. We demonstrate that also for InP, an oxide free interface does not solve the passivation problem.
19 February 2024 in Japanese Journal of Applied Physics
We investigated chemical mechanical polishing (CMP) of indium, with the goal of obtaining indium bond pads for later cryo-3D integration of quantum computing-related chips, through bonding between these bond pads and indium bumps. Higher removal rates were obtained with soft CMP pads than with hard pads. The latter led to deep scratching, while this effect was much more limited for soft pad CMP. On patterned wafers, indium is cleared well in structured areas using soft pad CMP, leading to relatively high-quality indium surfaces inside bond pads, although corrosion might be of some concern. Pattern density uniformity was an important factor for within-die deviation in indium clearing time. Dishing was much more limited than in earlier work on indium polishing, while surface roughness was also found to be relatively limited. The obtained indium damascene bond pads may be suitable for 3D die-to-die and wafer-to-wafer bonding through indium pad-to-bump bonding.
Semiconductor manufacturing is a resource and energy-intensive industry with a substantial environmental footprint. To address the footprint, we present a methodology for quantifying the environmental impact of semiconductor unit processes using the Environmental Footprint 3.1 Life Cycle Impact Assessment (LCIA) framework, focusing on identifying improvement opportunities in process steps with less sensitivity to defects. We apply this methodology to backside wet cleaning by proposing an alternative single-wafer process that adopts ozonated chemistries. The assessment used primary data from imec’s 300 mm pilot line. Results show that the proposed process reduces the total environmental footprint by 55% compared to the baseline Spin Cleaning with Repetitive use of Ozonated water and Diluted HF process. Key reductions include 67% less electricity for cleaning, 59% less HF use, and a 31% reduction in ultrapure water consumption. When scaled to a facility producing N28 Logic wafers at 50,000 wafer starts per month, with 46 backside clean steps per processed wafer, the process achieves annual savings of approximately 4 million kWh of electricity and 28 million liters (28,000 m3) of tap water per year. A sensitivity analysis revealed that replacing fossil-based electricity with hydroelectric power further reduces total environmental impacts by up to 63%, emphasizing the benefit of combining process innovation with renewable energy sourcing.