Jon Tomas Gudmundsson

Prof. Jon Tomas Gudmundsson

orcid

Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2006 in Thin Solid Films
Verified
Journal Article
Closed access
UHUlf Helmersson
Ulf Helmersson
MLMartina Lattemann
Martina Lattemann
JBJohan Bohlmark
Johan Bohlmark
AEArutiun Ehiasarian
Arutiun Ehiasarian
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson

14 March 2012 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson
NBN. Brenning
N. Brenning
DLDaniel Lundin
Daniel Lundin
UHU. Helmersson
U. Helmersson
The high power impulse magnetron sputtering (HiPIMS) discharge is a recent addition to plasma based sputtering technology. In HiPIMS, high power is applied to the magnetron target in unipolar pulses at low duty cycle and low repetition frequency while keeping the average power about 2 orders of magnitude lower than the peak power. This results in a high plasma density, and high ionization fraction of the sputtered vapor, which allows better control of the film growth by controlling the energy and direction of the deposition species. This is a significant advantage over conventional dc magnetron sputtering where the sputtered vapor consists mainly of neutral species. The HiPIMS discharge is now an established ionized physical vapor deposition technique, which is easily scalable and has been successfully introduced into various industrial applications. The authors give an overview of the development of the HiPIMS discharge, and the underlying mechanisms that dictate the discharge properties. First, an introduction to the magnetron sputtering discharge and its various configurations and modifications is given. Then the development and properties of the high power pulsed power supply are discussed, followed by an overview of the measured plasma parameters in the HiPIMS discharge, the electron energy and density, the ion energy, ion flux and plasma composition, and a discussion on the deposition rate. Finally, some of the models that have been developed to gain understanding of the discharge processes are reviewed, including the phenomenological material pathway model, and the ionization region model.

1 November 2020 in Plasma Sources Science and Technology
Verified
Journal Article
Open access
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson
Magnetron sputtering deposition has become the most widely used technique for deposition of both metallic and compound thin films and is utilized in numerous industrial applications. There has been a continuous development of the magnetron sputtering technology to improve target utilization, increase ionization of the sputtered species, increase deposition rates, and to minimize electrical instabilities such as arcs, as well as to reduce operating cost. The development from the direct current (dc) diode sputter tool to the magnetron sputtering discharge is discussed as well as the various magnetron sputtering discharge configurations. The magnetron sputtering discharge is either operated as a dc or radio frequency discharge, or it is driven by some other periodic waveforms depending on the application. This includes reactive magnetron sputtering which exhibits hysteresis and is often operated with an asymmetric bipolar mid-frequency pulsed waveform. Due to target poisoning the reactive sputter process is inherently unstable and exhibits a strongly non-linear response to variations in operating parameters. Ionized physical vapor deposition was initially achieved by adding a secondary discharge between the cathode target and the substrate and later by applying high power pulses to the cathode target. An overview is given of the operating parameters, the discharge properties and the plasma parameters including particle densities, discharge current composition, electron and ion energy distributions, deposition rate, and ionized flux fraction. The discharge maintenance is discussed including the electron heating processes, the creation and role of secondary electrons and Ohmic heating, and the sputter processes. Furthermore, the role and appearance of instabilities in the discharge operation is discussed.

1 October 2010 in Surface and Coatings Technology
Verified
Journal Article
Closed access
MSMattias Samuelsson
Mattias Samuelsson
DLDaniel Lundin
Daniel Lundin
JJJens Jensen
Jens Jensen
MRMichael A. Raadu
Michael A. Raadu
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson
UHUlf Helmersson
Ulf Helmersson

19 April 2007 in Plasma Sources Science and Technology
Verified
Journal Article
Closed access
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson
ETE G Thorsteinsson
E G Thorsteinsson

1 December 2006 in Thin Solid Films
Verified
Journal Article
Closed access
JBJ. Bohlmark
J. Bohlmark
MLM. Lattemann
M. Lattemann
JGJon Tomas Gudmundsson
Jon Tomas Gudmundsson
AEArutiun Ehiasarian
Arutiun Ehiasarian
YGY. Aranda Gonzalvo
Y. Aranda Gonzalvo
UHU. Helmersson
U. Helmersson