Surface NH2-functionalized SBA-15 mesoporous silica was synthesized using toluene diisocyanate (TDI) as a bridge molecule. First, the surface Si-OH groups of SBA-15 were reacted with the -NCO groups of TDI. Then, the remaining unreacted -NCO groups of TDI were reacted with the -NH2 groups of ethylenediamine (EDA). Finally, the NH2-groups were successfully grafted onto the mesoporous SBA-15 surface by the above two-step method. XRD, N2 adsorption-desorption analysis, FT-IR, and 29Si MAS NMR were used to identify the well-ordered structure and the successful incorporation of the -NH2 groups onto the surface of the synthesized materials. Characterizations revealed that such -NH2 grafting is an effective method to obtain a high loading of -NH2 groups onto the SBA-15. When subjected to toxic heavy metal ions in aqueous solution, the obtained NH2-functionalized SBA-15 showed very high adsorption rates 99.9%, 99.7%, 99.8%, 99.5% and 99.9% for Pb2+, Cr3+, Cd2+, Ag+ and the Cu2+, respectively, which is attributed to the strong complexation reactions between the metal ions and the grafted -NH2 groups.
Due to the depletion of fossil fuels, the demand for renewable energy has increased, thus stimulating the development of novel materials for energy conversion devices such as fuel cells. In this work, nickel nanoparticles loaded on reduced graphene oxide (Ni/rGO) with small size and good dispersibility were successfully prepared by controlling the pyrolysis temperature of the precursor at 450 °C, assisted by a microwave-assisted hydrothermal method, and exhibited enhanced electrocatalytic activity towards oxygen reduction reaction (ORR). Additionally, the electron enrichment on Ni NPs was due to charge transfer from the rGO support to metal nickel, as evidenced by both experimental and theoretical studies. Metal–support interactions between nickel and the rGO support also facilitated charge transfer, contributing to the enhanced ORR performance of the composite material. DFT calculations revealed that the first step (from O2 to HOO*) was the rate-determining step with an RDS energy barrier lower than that of the Pt(111), indicating favorable ORR kinetics. The HOO* intermediates can be transferred onto rGO by the solid-phase spillover effect, which reduces the chemical adsorption on the nickel surface, thereby allowing continuous regeneration of active nickel sites. The HO2− intermediates generated on the surface of rGO by 2e− reduction can also efficiently diffuse towards the nearby Ni surface or the interface of Ni/rGO, where they can be further rapidly reduced to OH−. This mechanism acts as the pseudo-four-electron path on the RRDE. Furthermore, Ni/rGO-450 demonstrated superior stability, methanol tolerance, and durability compared to a 20 wt% Pt/C catalyst, making it a cost-effective alternative to conventional noble metal ORR catalysts for fuel cells or metal–air batteries.
11 May 2020 in Reaction Kinetics, Mechanisms and Catalysis
Ethylene/1-octene copolymers exhibit enhanced flexibility and impact resistance compared to polyethylene, which makes them well suited for applications in advanced plastics and elastomers. United-atom molecular dynamics (MD) simulations were conducted to explore the mechanical behavior and deformation mechanisms of ethylene/1-octene copolymers under uniaxial tensile loading. This study systematically examined the influence of temperature, polymer chain length, chain quantity, and strain rate, with a specific focus on how hexyl branch content impacts the mechanical properties of amorphous ethylene/1-octene copolymers. The simulation results indicate that as the branch content increases, the yield strength and elastic modulus decrease, suggesting a trade-off between flexibility and mechanical strength. Energy decomposition analysis reveals that copolymers with more branched chains undergo greater changes in van der Waals energy. Additionally, as the branch content increases, the reduction in dihedral angle energy in the strain hardening region becomes more gradual, and the rate and the extent of the transition of dihedral angles from gauche to trans conformation decrease under deformation. Ethylene/1-octene copolymers exhibit higher chain entanglement parameters compared to linear polyethylene, with these parameters increasing as the branch content rises. Moreover, increasing the branch content results in a less pronounced increase in chain orientation along the loading direction.
The performance of ethylene/1-octene copolymer primarily depends on the microstructure of the polymer chain. This study employed a new method to control the inter-distribution of hexyl chain branches directly on the backbone of the ethylene/1-octene copolymer. Three ethylene/1-octene copolymers with different inter-distributions of hexyl chain branches were synthesized using [Me2Si(C5Me4) (NtBu)] TiCl2 (Ti–CGC) by different feeding sequences in the semi-continuous polymerization reaction system. The three copolymers were named according to the feeding sequence of the materials: ethylene/1-octene/Ti–CGC (EOC), 1-octene/Ti–CGC/ethylene (OCE), and ethylene/Ti–CGC/1-octene (ECO), respectively. The structure and properties of the copolymers were characterized using HT-GPC, 13C-NMR, DSC, WAXD, DMA, MI, and Uniaxial Tension Test. The results showed that the feeding sequence greatly affected the comonomer distribution of the molecular chains, molecular weight, molecular weight distribution, and chemical composition of the copolymers, consequently influencing their thermal performance and mechanical properties. Thus, it is probable that one could obtain an ethylene/1-octene copolymer with designed properties by controlling the feeding sequence during the ethylene/1-octene semi-continuous copolymerization process.
The development of polyolefin catalysts plays a pivotal role in driving advancements within the polyolefin industry. In this study, five ligands (L1–L5) and six Hf (Hf 1-5) and Zr (Zr-1) metal complexes with amido-quinoline-based ligands were successfully synthesized by a simple and efficient synthetic route. The new Hf (Hf 1-5) and Zr (Zr-1) complexes exhibit high thermal stability, moderate activity, and excellent 1-octene incorporation capability. As a result, they have been successfully utilized in high-temperature solution-phase polymerization to produce polyolefin elastomers (POEs). The electron-donating effect of the ligand was identified as a crucial factor contributing to the improved catalytic performance and comonomer incorporation capability. The steric effects of substituents on the ligand have little impact on the olefin copolymerization activity, molecular weight, and comonomer incorporation capability. The Hf-1 complex demonstrates outstanding copolymerization activity and comonomer incorporation (8.3 × 106 g polymer/(mol catalyst · h), 26 wt%), offering significant potential for large-scale operations and practical applications.