A model of spontaneous flow driven by capillary pressure in nanoporous media

In present paper, the mineral and fluid compositions of shale oil from the Songliao Basin are analyzed systematically using core samples, X-ray diffractometer (XRD), and gas chromatography (GC). The effects of shale mineral composition, pore size, temperature, and pressure on the mass density of the adsorbed layers are then studied utilizing molecular dynamics simulation. The results show that illite and quartz are predominant in the micro petrological components of the shale, and nC19 is the main carbon peak. The fluid consists primarily of n-alkane molecules, and nC19 is found to be representative of the shale oil composition. Moreover, the adsorbing effect of quartz-illite mixed wall is between that of a pure mineral wall (illite and quartz), indicating that the selection of a mixed wall is similar to the actual shale composition. If the pores are inorganic, the minimum pore size of only adsorption oil is smaller than the organic pores. The critical adsorption point of shale oil in inorganic pores is less than 3.2 nm. Furthermore, compared to pressure, the temperature has a more significant effect on fluid adsorption due to the correlation with the kinetic energy of alkane molecules. This research shows the oil occurrence status in inorganic matter nanopore with a mixed solid wall, and provides theoretical support for shale oil exploration.

With the rapid growth of energy consumption, enhanced oil recovery (EOR) methods are continually emerging, the most effective and widely used was polymer flooding. However, the shortcomings were gradually exposed. A novel decorated polyacrylamide might be a better alternative than polymer. In this work, the molecular structure and the properties reflecting the viscosity of decorated polyacrylamide, interfacial tension, and emulsification were examined. In order to better understand the interactions between decorated polyacrylamide and oil as well as the displacement mechanism, the displacement experiment were conducted in the etched-glass microscale model. Moreover, the coreflooding comparison experiments between decorated polyacrylamide and polymer were performed to investigate the displacement effect. The statistical analysis showed that the decorated polyacrylamide has excellent characteristics of salt tolerance, viscosity stability, and viscosification like polymer. Besides, the ability to reduce the interfacial tension in order 10⁻¹ and emulsification, which were more similar to surfactant. Therefore, the decorated polyacrylamide was a multifunctional polymer. The displacement process captured by camera illustrated that the decorated polyacrylamide flooded oil mainly by means of ‘pull and drag’, ‘entrainment’, and ‘bridging’, based on the mechanism of viscosifying, emulsifying, and viscoelasticity. The results of the coreflooding experiment indicated that the recovery of decorated polyacrylamide can be improved by approximately 11–16% after water flooding when the concentration was more than 800 mg/L, which was higher than that of conventional polymer flooding. It should be mentioned that a new injection mode of ‘concentration reduction multi-slug’ was first proposed, and it obtained an exciting result of increasing oil production and decreasing water-cut, the effect of conformance control was more significant.

Shale oil in China is widely distributed and has enormous resource potential. The pores of shale are at the nanoscale, and traditional research methods encounter difficulty in accurately describing the fluid flow mechanism, which has become a bottleneck restricting the industrial development of shale oil in China. To clarify the distribution and migration laws of fluid microstructure in shale nanopores, we constructed a heterogeneous inorganic composite shale model and explored the fluid behavior in different regions of heterogeneous surfaces. The results revealed the adsorption capacity for alkanes in the quartz region was stronger than that in the illite region. When the aperture was small, solid–liquid interactions dominated; as the aperture increased, the bulk fluid achieved a more uniform and higher flow rate. Under conditions of small aperture/low temperature/low pressure gradient, the quartz region maintained a negative slip boundary. Illite was more hydrophilic than quartz; when the water content was low, water molecules formed a “liquid film” on the illite surface, and the oil flux percentages in the illite and quartz regions were 87% and 99%, respectively. At 50% water content, the adsorbed water in the illite region reached saturation, the quartz region remained unsaturated, and the difference in the oil flux percentage of the two regions decreased. At 70% water content, the adsorbed water in the two regions reached a fully saturated state, and a layered structure of “water–two-phase region–water” was formed in the heterogeneous nanopore. This study is of great significance for understanding the occurrence characteristics and flow mechanism of shale oil within inorganic nanopores.

The development effect of water flooding in an ultra-low permeability reservoir is poor due to its poor physical properties and high shale content, so an experimental study of air flooding which helps to complement energy production was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can undergo low-temperature oxidation reactions, which are the basic condition for air flooding. Three groups of experimental natural cylinder cores designed for oil displacement, water flooding and air flooding were used respectively, and the relationship between differential pressure, oil recovery, injection capacity with injection volume was investigated. It is observed that the recovery efficiency increased 2.58%, the injection-production pressure difference dropped 60% and the injection capability increased 60% in the experiment of shifting air flooding after water flooding to 75% moisture content, compared with water flooding alone. It has been shown in the results that the recovery efficiency improved sharply more than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was thus validated. We suggest that other science and technology workers should perform further tests and verify this result through numerical simulation.

Surface-active polymer is a novel multifunctional active polymer applied for enhancing oil recovery which has both viscosity-increasing ability and surface activity. Experiments were carried out to indicate basic physicochemical properties of surface-active polymer and to study on differences of properties between surface-active polymer and other chemical flooding agents, and characteristics of increasing displacement efficiency by surface-active polymer flooding have been tested. Experimental results show that the molecular aggregation conformation, viscosity performance and flow capacity of surface-active polymer were significantly different from those of other chemical flooding agents. Positive effects of viscosity and viscoelastic properties and improvements in interfacial chemical properties are basic characteristics of increasing displacement efficiency by surface-active polymer flooding which are basic principles of surface-active polymer flooding for enhancing oil recovery.