Thomas Bareth

Mr. Thomas Bareth

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
TBThomas Bareth
Thomas Bareth
NFNiklas Fromm
Niklas Fromm
MLMaja Lehmann
Maja Lehmann
GSGeorg Schlick
Georg Schlick
CSChristian Seidel
Christian Seidel
Powder bed fusion of metals using a laser beam (PBF-LB/M) enables the production of smart components by facilitating the integration of sensors almost anywhere within a part through its layer-by-layer manufacturing process. This allows for sensor placement near critical points of interest while providing protection against environmental influences. This study introduces a novel methodology for integrating bonded linear foil strain gauges within PBF-LB/M components—an approach not previously explored. The objective was to achieve reproducible in-situ monitoring of strain loads in components, with strain gauges integrated flexibly and cost-effectively during the PBF-LB/M process. Key steps included assessing the temperature at the integration position, selecting a suitable adhesive, preparing the bonding surface to optimize adhesion, designing appropriate cavities for sensors and wiring, and establishing guidelines for manual integration of the strain gauge within the PBF-LB/M environment. The feasibility of this integration methodology was successfully validated through strain measurements obtained from tensile tests on a sample with an integrated strain gauge. The measurement signal demonstrated a faithful measurement of strain and exhibited minimal deviations between repeated measurements.

13 June 2025 in Production Engineering
Verified
Journal Article
Open access
PDF file
TBThomas Bareth
Thomas Bareth
DEDaniel Eder
Daniel Eder
TSTimo Schroeder
Timo Schroeder
MLMaja Lehmann
Maja Lehmann
GSGeorg Schlick
Georg Schlick
CSChristian Seidel
Christian Seidel
This study presents the implementation of a novel nozzle-based powder deposition mechanism designed for three-material powder bed fusion using a laser beam. The research outlines the hardware configuration, featuring a six-axis articulated robot to maneuver the powder deposition system within the PBF-LB machine. The deposition system and powders were optimized to achieve three primary objectives: precise powder dosing, selective powder deposition, and homogenization of the powder layer. These investigations are essential and foundational for enabling applications that require three-material processing, such as the targeted production of battery cell caps. Battery cell caps require pure aluminum, pure copper, and an electrically insulating material (in this case a ceramic mixture). The aluminum powder is applied using the machine’s conventional recoater system. To facilitate the deposition of the second and third materials, the additional nozzle-based deposition mechanism must be integrated into the machine. Consequently, this study focuses on the deposition behavior of copper and ceramic powders using the nozzle mechanism. Through analysis of powder rheology, morphology, and granulometry, experimental insights were gained to understand, design, and optimize the deposition mechanism. The findings were used to examine flow-optimized powder composition and powder throughput. Following this, single and multiple powder tracks were deposited in the build chamber to evaluate the deposited track widths. Finally, the derived insights and scientific understanding were synthesized into guidelines, to provide a framework for applying the methodology to other powder materials for future applications.

1 May 2025 in Materials & Design
Verified
Journal Article
Open access
TBThomas Bareth
Thomas Bareth
DEDaniel Eder
Daniel Eder
MLMaja Lehmann
Maja Lehmann
GSGeorg Schlick
Georg Schlick
CSChristian Seidel
Christian Seidel

20 April 2026 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
TBThomas Bareth
Thomas Bareth
MKMalte Kroeger
Malte Kroeger
MSMichael Schmidt
Michael Schmidt
MLMaja Lehmann
Maja Lehmann
GSGeorg Schlick
Georg Schlick
CSChristian Seidel
Christian Seidel
The early development of prismatic battery cells requires a rapid and flexible supply of housings in small quantities. Conventional manufacturing methods such as deep drawing or impact extrusion are time- and cost-intensive due to the need for specialized tooling with fixed geometry. Bending with welding or machining also has limitations for thin-walled designs. Additive Manufacturing (AM) via powder bed fusion of metals using a laser beam (PBF-LB/M) enables tool-free and geometrically flexible production, making it suitable for the time-efficient manufacturing of small batches, such as for iterative design adjustments. This study investigates the PBF-LB/M fabrication of thin-walled battery cell cans made of pure aluminum. To address the main challenge of process-induced distortion, several strategies were evaluated and assessed for suitability in two standardized formats for prismatic battery cells defined in DIN 91252:2016-11. These strategies include simulation-based pre-deformation, contactless support, a varied scan strategy, build plate heating, and stress-relief heat treatment. A novel direct support strategy was developed, enabling reproducible manufacturing with maximum out-of-plane distortion below 0.25 mm, measured via structured-light 3D scanning, in the BEV4 format. Post-processing by two-stage vibratory finishing achieved a surface roughness under 3 \(\upmu\)m, meeting functional requirements. Helium leak testing confirmed hermetic sealing with leak rates below 2.57\(\times 10^{-6}\) mbar L s\(^-1\).

3 February 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TBThomas Bareth
Thomas Bareth
DEDaniel Eder
Daniel Eder
FSFlorian Steinlehner
Florian Steinlehner
MLMaja Lehmann
Maja Lehmann
GSGeorg Schlick
Georg Schlick
CSChristian Seidel
Christian Seidel
This paper explores the economic feasibility of Additive Manufacturing (AM) for producing prismatic battery cell housings, specifically targeting small production runs. A comprehensive cost analysis was conducted to compare AM with Tool-Based Manufacturing (TM) processes for battery cell caps and cans. This analysis takes various factors, including tooling, materials, machinery, labor, and part finishing costs, into account. The study demonstrates that AM offers significant economic advantages over TM for single-digit and low double-digit batch sizes, primarily due to the absence of expensive tooling costs associated with TM. AM-produced battery cell cans continue to be cost-effective even for medium-sized production runs. Additionally, AM allows for the integration of sensors directly within battery cell caps, providing enhanced real-time monitoring capabilities–an important benefit for development purposes. Further analysis, assuming a best-case scenario, indicated potential cost savings through the use of increased layer heights and faster recoating and scanning speeds, which enhances the economic appeal of AM. Overall, the findings suggest that AM is particularly beneficial for the production of battery cell housings in low- to mid-volume ranges, emphasizing its strategic importance for flexible manufacturing requirements and research-intensive applications.

1 December 2025 in Nano Micro Mechanics Review
Verified
Journal Article
Closed access
TBThomas Bareth
Thomas Bareth
BRBjoern Ringel
Bjoern Ringel
VSVeronika Stapff
Veronika Stapff
MLMaja Lehmann
Maja Lehmann
MHMax Horn
Max Horn
CSChristian Seidel
Christian Seidel