Currently, materials with specific, strictly defined functional properties are becoming increasingly important. A promising strategy for achieving these properties involves developing methods that facilitate the formation of hierarchical porous materials that combine micro-, meso-, and macropores in their structure. Macropores facilitate effective mass transfer of substances to the meso- and micropores, where further adsorption or reaction processes can occur. Aerogels represent a promising class of materials for implementing this approach. The formation of hierarchical porous structures in aerogels can be achieved using soft and hard templating methods or by foaming techniques. This paper presents a comprehensive study of three methods for forming hierarchical porous structures in alginate aerogels: (1) employing surfactants (Pluronic F-68), (2) using zein as a pore-forming component, and (3) foaming in a carbon dioxide medium. The results of micro-CT showed that each of the methods contributes to the formation of macropores within the structure of the resulting aerogels. Size distribution curves of the detected macropores were obtained, showing the presence of macropores ranging from 16 to 323 μm in size for samples obtained using surfactants, from 5 to 195 μm for samples obtained using zein, and from 20 μm to 3 mm for samples obtained by foaming in a carbon dioxide medium. The SEM images demonstrated the macro- and mesoporous fibrous structure of the obtained materials. The nitrogen porosimetry results indicated that samples obtained using surfactants and zein are characterized by a high specific surface area (592–673 m2/g), comparable to the specific surface area for an alginate-based aerogel obtained without the use of pore-forming components. However, the use of the developed methods for the formation of a hierarchical porous structure contributes to an increase in the specific mesopores volume (up to 17.7 cm3/g). The materials obtained by foaming in a carbon dioxide medium are characterized by lower specific surface areas (112–239 m2/g) and specific mesopores volumes (0.6–2.1 cm3/g). Thus, this paper presents a set of methods for forming hierarchical porous structures that can obtain delivery systems for active substances with a controlled release profile and highly efficient platforms for cell culturing.
Currently, materials with specific, strictly defined functional properties are becoming increasingly important. A promising strategy for achieving these properties involves developing methods that facilitate the formation of hierarchical porous materials. Aerogels represent a promising class of materials for implementing this approach. The synthesis of aerogels based on biopolymers exhibiting a hierarchical porous structure—combining micropores, mesopores, and macropores—enables the development of active substance delivery systems with controlled release profiles and highly efficient platforms for cell cultivation. The formation of hierarchical porous structures in aerogels can be achieved using soft and hard templating methods or by foaming techniques. This paper presents a comprehensive study of three methods for forming hierarchical porous structures in alginate aerogels: (1) employing surfactants (Pluronic F-68), (2) using zein as a pore-forming component, and (3) foaming in a carbon dioxide environment. The results of computed X-ray microtomography (micro-CT), scanning electron microscopy (SEM) and nitrogen porosimetry are presented. For each method of forming hierarchical porous structures, we investigated the effects of various parameters on the structural characteristics of the resulting material: for method (1), the surfactant concentration (0.25-1.00 wt.%); for method (2) – alginate-to-zein ratio (20:1, 10:1, 5:1); and for method (3) – pressure (50 and 100 bar) and holding time (1 and 3 hours). The results of micro-CT showed that each of the methods contributes to the formation of macropores within the structure of the resulting aerogels. Size distribution curves of the detected macropores were obtained, showing the presence of macropores ranging from 16 to 323 micrometers in size for samples obtained using surfactants, from 5 to 195 micrometers for samples obtained using zein, and from 20 micrometers to 3 mm for samples obtained by foaming in a carbon dioxide medium. The SEM images demonstrated the macro- and mesoporous fibrous structure of the obtained materials. The nitrogen porosimetry results indicated that samples obtained using surfactants and zein are characterized by a high specific surface area (592-673 m2/g), comparable to the specific surface area for an alginate-based aerogel obtained without the use of pore-forming components. However, the use of the developed methods for the formation of a hierarchical porous structure contributes to an increase in the specific mesopores volume (up to 17.7 cm3/g). The materials obtained by foaming in a carbon dioxide medium are characterized by lower specific surface areas (112-239 m2/g) and specific mesopores volumes (0.6-2.1 cm3/g). Thus, this paper presents a set of methods for forming hierarchical porous structures, wherein macropores facilitate effective mass transfer of substances to meso- and micropores, where subsequent adsorption or reaction processes occur.
Additive manufacturing of hydrogel-based scaffolds requires concurrent control of material rheology and extrusion dynamics, especially in multi-material architectures. In this work, we develop a modular multi-material extrusion-based 3D-printing platform that combines a filament-fed extruder for thermoplastic polymers with a piston-driven extruder for viscous gel inks, together with an empirical calibration procedure for gel dosing. The calibration algorithm optimizes the pre-extrusion and retraction displacement (EPr/R) based on stepwise extrusion experiments and reduces the discrepancy between theoretical and measured deposited mass for shear-thinning alginate gels to below the prescribed tolerance. The calibrated system is then used to fabricate two representative hybrid constructs: partially crosslinked sodium alginate scaffolds with an internal hollow channel supported by a removable polycaprolactone framework, and self-supporting structures based on a sodium alginate–chitosan polyelectrolyte complex obtained by sequential co-extrusion. The resulting constructs remain mechanically stable after ionic crosslinking and solvent treatment and can subsequently be converted into highly porous scaffolds by freeze- or supercritical drying. The proposed combination of hardware architecture and extrusion calibration enables reproducible multi-material 3D printing of hydrogel–thermoplastic hybrid scaffolds and can be readily adapted to other gel-based inks for tissue engineering applications.
Additive manufacturing is one of the most efficient approaches for fabricating components with complex geometries. Among the wide variety of additive manufacturing technologies, extrusion-based processes using gel materials are attracting increasing attention from researchers. In this work, we consider the extrusion of gel materials for 3D printing and propose a method for calibrating additive manufacturing equipment based on optimization of the pre-extrusion and retraction parameters. Experimental studies were carried out on the extrusion of materials with different rheological properties. The capabilities of the proposed calibration method to improve printing quality are demonstrated using gel materials based on partially crosslinked sodium alginate with a viscosity of 1053 Pa·s. A multi-material 3D printing process was also implemented, enabling the combination of different materials within a single fabrication process. To realize the proposed 3D printing approach, we present a custom-built setup that allows the use of two extrusion modules for materials with different physicochemical properties. The capabilities of the developed system are demonstrated by fabricating a structure with an internal hollow channel and a structure based on a sodium alginate–chitosan polyelectrolyte complex.
Additive manufacturing makes it possible to create objects with complex geometry for various applications, including personalized implants. Hydrogel scaffolds with shape-morphing effects are of particular interest in the field of soft tissue engineering. This work describes the technology of extrusion-based 3D printing of objects of complex spatial shape based on biopolymer viscous ink. A technique for producing viscous ink based on sodium alginate, hydroxypropylmethylcellulose and silver nanoparticles embedded in a polymer matrix has been developed. The sizes of silver nanoparticles were determined via dynamic light scattering. The colloidal stability of silver nanoparticles was assessed by analyzing the peak of surface plasmon resonance using UV-VIS spectroscopy. The compliance of the developed viscous ink with the requirements for materials for extrusion-based 3D printing was confirmed by the results of comprehensive rheological research. The main patterns of the relationship between the infill pattern parameters during 3D printing and the degree of deformation of hydrogel structures resulting from anisotropic swelling of sections of various thicknesses have been identified. The developed Alg3/HPMC3/AgNPs scaffolds exhibited preliminary cytocompatibility and supported cell viability. The deformation of hydrogel structures was modeled using finite element analysis, which enables the prediction of their spatial shape for further design of personalized cartilage implants.