Flexible electronics have gained eminent importance in recent years due to their high mechanical strength and resistance to environmental conditions, along with their effective energy storage and energy generating abilities. In this work, graphene/ceramic/polymer based flexible dielectric nanocomposites have been prepared and their dielectric properties were characterized. The composite was formulated by combining graphene with rutile and anatase titania, and polyvinylidene fluoride in different weight ratios to achieve optimized dielectric properties and flexibility. After preparation, composites were characterized for their morphologies, structures, functional groups, thermal stability and dielectric characterizations by using scanning electron microscopy, X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, thermal gravimetric analysis and impedance spectroscopy. Dielectric results showed that prepared flexible composite exhibited dielectric constant of 70.4 with minor leakage current (tanδ) i.e., 0.39 at 100 Hz. These results were further confirmed by calculating alternating current (AC) conductivity and electric modulus which ensured that prepared material is efficient dielectric material which may be employed in electronic industry for development of next generation flexible energy storage devices.

To address the limitations of piezoelectric polymers which have a low dielectric constant andto improve their dielectric and ferroelectric efficiency for energy storage applications, we designed and characterized a new hybrid composite that contains polyvinylidene fluoride as a dielectric polymer matrix combined with graphene platelets as a conductive and barium titanite as ceramic ferroelectric fillers. Different graphene/barium titanate/polyvinylidene fluoride nanocomposite films were synthesized by changing the concentration of graphene and barium titanate to explore the impact of each component and their potential synergetic effect on dielectric and ferroelectric properties of the composite. Results showed that with an increase in the barium titanate fraction, dielectric efficiency ofthe nanocomposite was improved. Among all synthesized nanocomposite films, graphene/barium titanate/polyvinylidene fluoride nanocomposite in the weight ratio of 0.15:0.5:1 exhibited thehighest dielectric constant of 199 at 40 Hz, i.e., 15 fold greater than that of neat polyvinylidene fluoride film at the same frequency, and possessed a low loss tangent of 0.6. However, AC conductivity and ferroelectric properties of graphene/barium titanate/polyvinylidene fluoride nanocomposite films were enhanced with an increase in the graphene weight fraction. Graphene/barium titanate/polyvinylidene fluoride nanocomposite films with a weight ratio of 0.2:0.1:1 possessed a high AC conductivity of 1.2 × 10⁻⁴ S/m at 40 Hz. While remanent polarization, coercive field, and loop area of the same sample were 0.9 μC/cm², 9.78 kV/cm, and 24.5 μC/cm²·V, respectively. Our results showed that a combination of graphene and ferroelectric ceramic additives are an excellent approach to significantly advance the performance of dielectric and ferroelectric properties of piezoelectric polymers for broad applications including energy storage.

Organic manures are more preferred and environmentally friendly than chemical fertilizers for minimally contaminating soil, water and environmental resources, but the determination of right source of organic manures continues to remain an unexplored aspect. Considering the important issue, a multi-year field trial was carried out to determine the response of forage soybean to four sources of nutrients such as chemical fertilizers (IF), poultry litter (PL), bovine’s farm yard slurry (BFYS) and sewage sludge (SS) and their seven binary combinations (PL+BFYS, PL+SS, PL+IF, BFYS+SS, BFYS+IF, SS+IF and PL+BFYS+SS). Supplementation of organic manures with mineral fertilizers remained superior to their sole application, particularly BFYS + IF was found significantly (p≤0.05) superior for yielding the highest fresh biomass (23.9, 26.4 and 25.7 t ha^–1) with improved nutritional quality. The same combination of integrated fertilizer management also recorded higher sustainability as per sustainable forage yield index along with the highest net income and the benefit-cost ratio. PL and SS applied in conjunction with IF performed better than sole or binary application of organic manures. Therefore, BFYS + IF may be recommended for adoption to produce comparable forage yield and nutritional quality of soybean along with reducing dependency on chemical fertilizers.

Suspension microsphere immunoassays are rapidly gaining attention in multiplex bioassays. Accurate detection of multiple analytes from a single measurement is critical in modern bioanalysis, which always requires complex encoding systems. In this study, a novel bioassay with Raman-coded antibody supports (polymer microbeads with different Raman signatures) and surface-enhanced Raman scattering (SERS)-coded nanotags (organic thiols on a gold nanoparticle surface with different SERS signatures) was developed as a model fluorescent, label-free, bead-based multiplex immunoassay system. The developed homogeneous immunoassays included two surface-functionalized monodisperse Raman-coded microbeads of polystyrene and poly(4-tert-butylstyrene) as the immune solid supports, and two epitope modified nanotags (self-assembled 4-mercaptobenzoic acid or 3-mercaptopropionic acid on gold nanoparticles) as the SERS-coded reporters. Such multiplex Raman/SERS-based microsphere immunoassays could selectively identify specific paratope–epitope interactions from one mixture sample solution under a single laser illumination, and thus hold great promise in future suspension multiplex analysis for diverse biomedical applications.

Textile wastewater effluents carry synthetic dyes resulting in potential hazards to the environment; hence such dyes need to be removed from the water bodies. In present research work, disperse dyes were degraded through coagulation using alum (Al₂(SO₄)₃.18H₂O) as a coagulant. Four dyes namely coralene navy blue EMRD, coralene red 6B, coralene orange 3R and coralene scarlet RR were used in the present research work and their removal from the wastewater was determined. The effects of initial pH, coagulant dose, initial dye concentration, temperature and time of reaction were tested to maximise decolourisation yield. Results of the experiments showed that the optimum pH for coagulation was 9 for each dye with up to 99% colour removal. By increasing the dose of alum Al₂(SO₄)₃.18H₂O, dye decolourisation was increased and maximum dye removal was observed when 1000 ppm of Al₂(SO₄)₃.18H₂O was used. When 100 ppm synthetic dye solution was prepared, up to 99% colour removal was achieved at optimal conditions i.e pH = 9, 1000 ppm of coagulant at 100°C with 50 min reaction time. Coralene navy blue EMRD presented nearly 70% colour removal with lowest dose of alum (200ppm) at 40°C. About 80% dye degradation was observed for coralene orange 3R within 10 min of reaction time. Thus Al₂(SO₄)₃.18H₂O was found to be efficient coagulant for the treatment of wastewater containing disperse dyes with about 50% reduction in conductivity and upto 75% removal in TDS of wastewater. Sludge volume settled after 1 hour of reaction time was 140 mL/500 mL. On the basis of obtained results, it was concluded that the wastewater can be treated using Al₂(SO₄)₃.18H₂O as coagulant.