Guang Liu

Dr. Guang Liu

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 December 2024 in Applied Thermal Engineering
Verified
Journal Article
Closed access
HWHe-Chen Wang
He-Chen Wang
SZShao-Fei Zheng
Shao-Fei Zheng
GLGuang Liu
Guang Liu
KYKai-Xin Yan
Kai-Xin Yan
YYYan-Ru Yang
Yan-Ru Yang
XWXiao-Dong Wang
Xiao-Dong Wang

6 May 2020 in Journal of Thermal Science
Verified
Journal Article
Closed access
PDF file
RWRuonan Wang
Ruonan Wang
QDQiang Du
Qiang Du
GLGuang Liu
Guang Liu
ZLZengyan Lian
Zengyan Lian
LXLei Xie
Lei Xie
JZJunqiang Zhu
Junqiang Zhu

27 February 2023 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
DQDu Qiang
Du Qiang
WRWang Ruonan
Wang Ruonan
XLXie Lei
Xie Lei
GLGuang Liu
Guang Liu
ZLZengyan Lian
Zengyan Lian
Rim seal structures and sealing flows are essential in aero engines for preventing hot gas ingestion from mainstream to turbine disk cavities. A novel design method of rim sealing flow path based on auxiliary sealing holes and sealing air re-distributions has been proved to improve sealing effectiveness. The present paper uses this method to re-design the axial rim sealing flow in a high-pressure turbine front cavity in an engine turbine. The incidence angle of the auxiliary sealing air has been proved to have a significant influence on sealing performance. Three different incidence angles, 0-deg, 35-deg, and 70-deg, with the maximum angle close to the vane exit flow angle, are investigated using unsteady computational fluid dynamics methods validated by experimental data. Sealing effectiveness, swirl ratio, unsteady flow structures in both rim clearance and wheel space cavity are considered. The auxiliary sealing air with a swirl in the circumferential direction is proved to improve and uniform swirl ratio and suppress flow instabilities. This results in a reduction in hot gas ingestion and a considerable improvement in sealing effectiveness. The mechanisms of improving sealing effectiveness using this novel method are explained. The conclusions may support the understanding of the complex flow mechanisms near the rim seal, provide references for the design of this novel structure and give possibilities to improve rim seal performance and engine efficiency.

22 February 2020 in International Journal of Aerospace Engineering
Verified
Journal Article
Open access
PDF file
GLGuang Liu
Guang Liu
QDQiang Du
Qiang Du
JLJun Liu
Jun Liu
PWPei Wang
Pei Wang
RWRuoNan Wang
RuoNan Wang
ZLZengYan Lian
ZengYan Lian
In typical median and small aeroengines, the air used to realize the functions such as cooling of turbine blades and disks, sealing of turbine cavities and bearing chambers, adjusting of rotating assembly axial load is normally drawn through the rear cavity of centrifugal impeller, so the thorough understanding of flow characteristics and pressure distribution and the proposal of the corresponding control methods in the cavity are the key to design the rational secondary air system. With an impeller rear cavity in a small turbofan engine as an object, the current study was dedicated to the investigation of flow control methods in the cavity. Two methods, namely, baffle and swirl-controlled orifice, were proposed to regulate the pressure loss and distribution in the cavity. Furthermore, the influence of geometry parameters of the two methods such as the length of baffle, the space between the baffle and rotating disk wall, the orientation, and radial position of swirl-controlled orifice was investigated. The CFD results show that the swirl-controlled orifice which could deswirl the flow is more effective in regulating the pressure loss and its distribution in cavity than baffle. The variation of the radial position of the swirl-controlled orifice had little influence on pressure loss but obvious influence on pressure distribution; therefore, decreasing the radial position could reduce the axial load on the rotating disk without changing the outlet pressure.

25 August 2020 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Verified
Journal Article
Closed access
PDF file
JLJun Liu
Jun Liu
HLHongrui Liu
Hongrui Liu
GLGuang Liu
Guang Liu
QDQiang Du
Qiang Du
PWPei Wang
Pei Wang
SCSheng Chang
Sheng Chang
After being studied for years, aggressive intermediate turbine duct is being attempted to be applied in turbine design to further improve the engine-performance. With such design, the shaft could be shortened effectively. However, under the influence of the more distorted coming-flow and stronger pressure-gradient in a real engine, the flow field would be more complicated definitely. Besides that, the upstream-rotor tip-leakage flow is a key loss-source by inducing separation. Flow-control strategies are necessary in this situation. In this paper, the flow field in an aggressive duct has been analyzed to declare the source of separation primarily. Then wide-chord blade design concept has been adopted as a control strategy firstly to realize the purpose of improving the areo-performance. After being verified, numerical method has been used in this study. Under the same aero-condition, the prototype and the modified turbine are analyzed. With this novel flow-control strategy, separation has been improved, even diminished. However, the flow structures within the blade passage are altered correspondingly. An instrumental conclusion is that the pressure loss could be decreased successfully by designing the wide-chord blade specially.

10 May 2024 in Journal of Thermal Science
Verified
Journal Article
Closed access
PDF file
RRRan Ren
Ran Ren
QDQiang Du
Qiang Du
GLGuang Liu
Guang Liu
YZYanlian Zeng
Yanlian Zeng
LXLei Xie
Lei Xie