Vehicle exhaust gases remain one of the key sources of atmospheric air pollution and pose a serious threat to ecosystems and public health. This study presents an experimental investigation into reducing the toxicity of gasoline internal combustion engine exhaust using ultrasonic waves and infrared (IR) laser exposure. An original hybrid system integrating an ultrasonic emitter and an IR laser module was developed. Four operating modes were examined: no treatment, ultrasound only, laser only, and combined ultrasound–laser treatment. The concentrations of CH, CO, CO2, and O2, as well as exhaust gas temperature, were measured at idle and under operating engine speeds. The experimental results show that ultrasound provides a substantial reduction in CO concentration (up to 40%), while IR laser exposure effectively decreases unburned hydrocarbons CH (by 35–40%). The combined treatment produces a synergistic effect, reducing CH and CO by 38% and 43%, respectively, while increasing the CO2 fraction and decreasing O2 content, indicating more complete post-oxidation of combustion products. The underlying physical mechanisms responsible for the purification were identified as acoustic coagulation of particulates, oxidation, and photodissociation of harmful molecules. The findings support the hypothesis that combined ultrasonic and laser treatment can enhance real-time exhaust gas purification efficiency. It is demonstrated that physical treatment of the gas phase not only lowers the persistence of by-products but also promotes more complete oxidation processes within the flow.
When developing the system, the company sought to minimize changes to the existing engine design, which largely determined the chosen layout. Furthermore, when developing the fuel system, it was necessary to take into account the protective effects of numerous patents, which influenced a number of design decisions. Common rail fuel systems for diesel engines in high-speed vehicles vary significantly in circuit design and the structure of individual components. Therefore, the most common design variations of these systems are discussed below. The fuel system design largely depends on the engine cylinder volume. The low-pressure fuel pump supplies the required fuel to the high-pressure fuel pump. A pressure-reducing valve maintains a constant pressure at the inlet of the high-pressure fuel pump section, located in the housing. As the name suggests, high-pressure fuel pumps are designed to create high pressure in the fuel line, which must always be significantly higher than the pressure in the engine cylinder, which is necessary for the normal operation of all similar fuel injection systems. To ensure stable operation of the high-pressure sections of diesel engines and effective lubrication of their supporting structures, a supply pressure of 0.5–0.8 MPa is required.
30 December 2024 in Science and Technology of Kazakhstan
Көлік кәсіпорындарының өндірістік қызметінде әлеуметтік – экономикалық жағдайға, өндірістік сипаттағы объективті себептер кешеніне, тиісті материалдық – техникалық базалардың болуына, оларды тиімді пайдалануға және кәсіпорындардың сапалы менеджментіне байланысты олардың экономикалық және еңбек шығындарын оңтайландыру мәселелері маңызды орын алады. Бұл жұмыста қазіргі жағдайда автомобильдерге техникалық қызмет көрсету станцияларының (ТҚКС) жұмыс бағдарламасын (тапсырыс портфолиосын) қалыптастыру ерекшеліктері келтірілген және олардың тұрақтылығын қамтамасыз етуге баса назар аударылған. Жұмысты жазудың негізгі әдісі - математикалық модельдеу, математикалық және статистикалық талдау әдістері және басқалар. Жұмыста ТҚКС өндірістік бағдарламасы кездейсоқ тәртіппен кәсіпорынға түсетін істен шығулар мен ақаулардың қосындысы ретінде ұсынылған. Эксперименттік зерттеулердің нәтижелері ықтималдықтар теориясы мен математикалық статистиканың ережелері негізінде өңделген, жылдық бағдарламаның математикалық модельдері және оны берілген уақыт аралығында бөлу ықтималдығы алынған. ТҚКС құрылымдарының біркелкі жүктелуін қамтамасыз ету арқылы өндірістік бағдарламаны оңтайландыру бойынша іс-шаралар ұсынылған. Сондай-ақ, белгілі бір нәтижелерге негізделген теориялық әдістер бар. Бұл зерттеуде автокөлік мекемелерін жобалау саласындағы эксперименттік-теориялық зерттеулер келтірілген және кәсіпорынға келетін көлік санын топтастыру негізінде жылдық бағдарламаны есептеу әдісі негізделген. Кілтті сөздер: автокөліктендіру; автокөлік құралдары, техникалық қызмет станциясы, Пуассон заңы, кездейсоқ процестер, регрессия теңдеулері.
1 January 2025 in Bulletin of L.N. Gumilyov Eurasian National University. Technical Science and Technology Series
The article presents a comparative analysis of the specific pressure exerted on the cylinder wall by a traditional compression piston ring and an alternative design consisting of two half-rings. The study focuses on the theoretical aspects of the formation and distribution of contact pressure between the piston ring and the cylinder wall. Mathematical models describing the stress-strain state of the ring when installed in the cylinder are provided, along with a simplified approach to calculating pressure for the two half-ring design without considering material elasticity. The calculations revealed that the traditional solid ring produces a non-uniform pressure diagram with peak values, which may contribute to accelerated wear of cylinder-piston group (CPG) components. In contrast, the pressure distribution generated by the two half-ring configuration is uniform, ensuring consistent load on the cylinder wall and reducing localized overloads, friction, and thermal deformations. The graphical dependencies and Fourier series approximations confirm the model’s agreement with real-world operating conditions. The paper also offers recommendations for selecting ring materials and geometric parameters to improve combustion chamber sealing and extend engine life. The authors emphasize that the implementation of a two half-ring configuration represents a promising direction for the modernization of piston rings in internal combustion engines, particularly under conditions of increased temperature and mechanical stress. The findings of this study may be of interest to engineers, researchers, and developers involved in the design and analysis of CPG components.
1 January 2024 in Bulletin of L.N. Gumilyov Eurasian National University. Technical Science and Technology Series
The article applies to similar conditions of use and the creation of a competitive two-stroke engine. Currently, there are prerequisites for creating an effective two-stroke engine, such as direct-flow scavenging, a valve-slotted gas distribution system with a multi-valve mechanism, hydraulic valve control, a diesel cycle with a high compression ratio, etc. To implement a set of promising technical solutions, a design basis is required, on the basis of which a two-stroke engine can be configured. As such, a crank-yoke kinematic mechanism for converting motion was chosen. The mechanism unloads the piston from lateral forces and allows the cylinder to be isolated from the oil sump, using the sub-piston volume as a purge pump. This required the development and research of a cylinder-piston group based on solid lubricant. The sliding bearing has also been improved with improved quality indicators based on the use of thermally conductive and antifriction materials of copper and graphite.