As robotic manipulators evolve toward lightweight and long-link structures, flexibility increasingly affects dynamic response and trajectory tracking accuracy. However, existing studies often lack a consistent coupling mechanism between finite element structural models and control models, and flexible effects are typically treated as disturbances, limiting the direct use of structural parameters for control prediction and optimization. This paper proposes a structure–control collaborative co-simulation framework for a six-degree-of-freedom (6-DOF) flexible-joint manipulator. ANSYS-based finite element analysis (FEA) is integrated with the MATLAB/Simulink control environment to extract joint-level equivalent stiffness, inertia, modal frequencies, and damping parameters, which are embedded into a rigid–flexible coupled dynamic model. A regression-based representation is introduced to capture unmodeled flexible residual dynamics, and a regression-compensated adaptive PID torque controller with σ-modification and a dead-zone mechanism is developed to ensure bounded adaptation and closed-loop stability. Simulation results under no-load and payload conditions demonstrate improved oscillation suppression and tracking accuracy. By establishing a unified coupling mechanism from structural parameters to the control model, the proposed method achieves consistent co-modeling of the structural and control domains and provides an engineering-feasible co-simulation approach for dynamic prediction and control optimization of multi-DOF flexible manipulators under varying operating conditions.
1 January 2024 in Bulletin of the South Ural State University Series "Power Engineering"
Simulink is a well-established electrical simulation software widely used in teaching electrical machines. However, it is limited to providing data results and cannot depict the real motion effects of actual motors. To address this problem, this paper establishes a mathematical simulation system in Simulink and a 3D virtual simulation system in Unity3D for a separately excited DC motor based on the concept of digital twins. A data transfer system between Simulink and the 3D platform is established via the UDP protocol, which realizes seamless data interaction between the two systems. Through the motor simulation experiment, the virtual experiment platform shows good real-time and accuracy. The 3D virtual simulation system can input data to the Simulink motor model and receive calculation results from the model in real time. The platform loads these results into the 3D motor model to visualize the corresponding motion effects. Users can customize the Simulink model according to their specific requirements and display the corresponding operating effects through the 3D virtual system via an independent data transmission system. The virtual experimental platform utilizes the 3D model to reproduce the running state of the motor and present the experimental results more intuitively and three-dimensionally. It overcomes the limitations of time and equipment. Simulink - это хорошо известное программное обеспечение для моделирования электрооборудования, широко используемое при изучении электрических машин. Однако оно ограничено в предоставлении результатов и не способно отобразить реальные эффекты движения физических двигателей. В данной работе разработана система математического моделирования в Simulink и система виртуального 3D-моделирования в Unity3D для двигателя постоянного тока с раздельным возбуждением, основанная на концепции цифровых двойников. Система передачи данных между Simulink и 3D-платформой создана на основе протокола UDP, обеспечивая бесперебойное взаимодействие между этими двумя системами. В ходе эксперимента по моделированию двигателя виртуальная экспериментальная платформа демонстрирует высокую скорость реакции и точность. Система виртуального 3D-моделирования может принимать входные данные из модели двигателя Simulink и получать результаты расчетов в реальном времени. Эти результаты затем загружаются в 3D-модель двигателя для визуализации соответствующих движений. Пользователи могут настраивать модель Simulink в соответствии со своими специфическими требованиями и отображать соответствующие рабочие эффекты через виртуальную 3D-систему с использованием независимой системы передачи данных. Виртуальная экспериментальная платформа использует 3D-модель для воспроизведения рабочего состояния двигателя и интуитивного трехмерного представления экспериментальных результатов. Это позволяет преодолеть ограничения по времени и доступному оборудованию.
End-effector obstacle-avoidance trajectory planning is essential for improving the autonomy, safety, and executability of industrial robotic manipulators in constrained workspaces. Conventional Rapidly Exploring Random Tree (RRT) planners provide effective exploration capability but often suffer from stochastic tree expansion, redundant trajectories, and insufficient directional guidance near obstacle regions, which limits planning efficiency and trajectory quality. This study proposes a clearance-field-guided RRT framework with behavior-cloning-assisted refinement for end-effector obstacle-avoidance trajectory planning of industrial robotic manipulators. The proposed method formulates the planning problem in Cartesian space based on an end-effector kinematic model and introduces local clearance-field guidance into the RRT sampling process. Candidate samples are evaluated by considering obstacle clearance, reference-line deviation, and goal distance, enabling the search tree to preferentially expand toward effective traversable regions while maintaining the exploration capability of conventional RRT. Behavior cloning is further introduced as an offline auxiliary strategy to investigate the influence of expert trajectories on local motion-direction learning and trajectory continuity. A Python–Unity joint simulation–verification framework and a physical manipulator experimental platform are established to evaluate the feasibility and practical executability of the generated trajectories. Python is used for offline trajectory generation, expert dataset construction, behavior-cloning training, and performance evaluation, while Unity is employed for three-dimensional manipulator modeling and trajectory reproduction. The experimental results demonstrate that the proposed Field-guided RRT achieves a better balance among path efficiency, planning time, obstacle-clearance maintenance, and trajectory execution capability compared with conventional RRT-based methods. The proposed framework provides an effective solution for collision-free end-effector trajectory planning in industrial applications such as assembly, welding, component placement, and robotic inspection.