This study aims to address the pronounced stress concentration in roadway-surrounding rock under conditions of multiple thick and hard roof strata at Xiao jihan coal mine, China. The work was carried out on the 13216 working mining face as the engineering background. A systematic investigation was conducted using a combination of theoretical analysis, numerical simulation, and field experiments. Under double mining disturbance, the lower thick hard roof behaves as a cantilever beam and the upper hard roof strata form a masonry beam structure, producing strong stress transfer to the roadway. The mechanical model indicates a peak stress of 28.90 MPa, 18.34 MPa higher than the in situ stress. Hydraulic roof cutting was designed at the upper thick hard roof horizon. UDEC simulations show that the vertical stress decreases from 26.10 MPa to 13.20 MPa. Field monitoring confirms pressure relief: the non-cutting zone shows a peak of 30.75 MPa, while the roof-cutting zone drops to 22.51 MPa, a 24.62% reduction. The findings of this study provide practical guidance for lateral structure regulation under similar geological and mining conditions.
To theoretically explain and quantify the effect of advancing speed (ADS) on ground pressure (GP) behavior, the 13,218 working face of the Xiaojihan Coal Mine (XCM) was taken as the engineering case. Field measurements and theoretical analysis were combined to examine how changes in ADS influence the roof structure and the support resistance. Considering the motion characteristics of key blocks, a calculation model for support resistance under multilayer thick hard roofs was established, incorporating the ADS factor. The results show that the overlying roof behaves as a composite system composed of a short cantilever beam and a voussoir beam structure, where the periodic fracture of the voussoir beam is the dominant cause of periodic weighting. When the ADS is accelerated from 5 to 15 m/day, the periodic weighting interval (PWI) grows by 29.1%, while the subsidence, rotation angle, and subsidence duration of key block C decrease by 39.1%, 53.5%, and 57.0%, respectively. The horizontal thrust between blocks increases by 31.6%, and the support resistance decreases by 7.9%. Comparison with field data (11,467–13,852 kN) shows the model predictions (11,549–13,757 kN) agree within 5%, verifying its reliability and applicability. The findings provide theoretical guidance for the optimization of advancing parameters and offer practical reference for GP control and safe, high‐intensity mining under multilayer hard roof conditions.
In response to ground pressure problems such as an abnormal increase in working face support resistance and severe roadway floor heave induced by the lateral composite structure of the multi-layer thick and hard roof in the 11,223 working face of Xiaojihan Coal Mine, based on the triangle area slip theory, this study reveals that the lateral triangle area forms a composite structure of “cantilever beam + masonry beam”. The stress transfer and unloading mechanism of the high- and low-position thick and hard rock stratum fracturing was clarified. A technical scheme is proposed and implemented to weaken the high- and low-position thick and hard rock strata through horizontal Long Directional Borehole synergistic fracturing and optimize stress transfer. The results show that (1) the lateral overlying rock forms a triangular slip area under the clamping of the cantilever and masonry beam structures. This composite structure is the main reason for the increase in the support resistance at the end of the working face and the stress concentration of the roadway surrounding rock. (2) The influence law that the load of the triangular slip area is mainly influenced by the length of the broken block, and the breaking angle was clarified. The distribution characteristics of the load in the lateral triangle area under the fracturing of thick and hard rock strata at different horizons are mastered. When the length of the key block is reduced by 40%, the supporting force F1 of the rock mass below the broken block on it is reduced by 62.5%, and the supporting force F2 and the frictional force F3 of the end part on the broken area of the triangle area are reduced by 34.6%. (3) The fracturing of high- and low-position thick and hard rock strata can collaboratively weaken the stress accumulation at high and low positions. Fracturing the low-position thick and hard rock strata can cut off the low-position “cantilever beam” structure, and fracturing the high-position thick and hard rock strata at the same time can transfer the load of the “masonry beam”. Through simulation, it is seen that the stress peaks at the end of the working face and the roadway surrounding rock during synergistic fracturing are, respectively, reduced by 12.2% and 28.9%. (4) An industrial test of directional drilling hydraulic fracturing of lateral thick and hard rock strata is carried out, achieving the regulation effect that the average value of the support resistance at the end of the cycle is reduced from 27.2 MPa to 22.7 MPa, and the floor heave amount of the reused roadway is reduced by 62.3%. The research results can provide a reference for the advanced treatment of the strong ground pressure area of the multi-layer thick and hard roof.