Yan Shen

Yan Shen


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 May 2019 in Materials
Verified
Journal Article
Open access
PDF file
WLWenhua Li
Wenhua Li
BYBaihong Yu
Baihong Yu
BYBin Ye
Bin Ye
YSYan Shen
Yan Shen
Ruoxuan HuangRuoxuan Huang
Ruoxuan Huang
Fengming DuFengming Du
Fengming Du
Advances in heavy-duty diesel engine designs place higher demands on the friction and wear performance of the piston ring and cylinder liner (PRCL) interface. The potential of using micro-textures machined on the whole stroke of a cast-iron cylinder liner was investigated in this work. A set of running-in and starved lubrication experiments was performed using a custom reciprocating test rig that imparts a combination of combustion-level pressures and the resulting impacts. Based on a comparison of micro-dimple parameters, the friction coefficient for the running-in period at the shocking dead center was the smallest at a designed combination of 1000-μm diameter, 22% area fraction, and arrangement with half-radius intersecting distance of two adjacent micro-dimple columns. The non-scuffing time under starvation was the longest at a designed combination of the following parameters: 800 μm diameter, 22% area fraction, and quarter-radius intersecting distance arrangement. From finite element analysis, it was found that stress concentrates at the micro-dimple periphery and at the connections between adjacent micro-dimples. However, surface topography examination showed that scuffing initiates in the non-dimpled regions between the micro-dimpled columns rather than at their edges. Finally, under reciprocating motion, micro-dimples can collect wear debris to inhibit further propagation of scuffing in the micro-dimpled region.

14 October 2017 in Materials
Verified
Journal Article
Open access
PDF file
YSYan Shen
Yan Shen
BYBaihong Yu
Baihong Yu
YLYutao Lv
Yutao Lv
BLBin Li
Bin Li
A running-in and starved lubrication experiment is designed to investigate the heavy-duty scuffing behavior of piston ring coatings against cast iron (Fe) cylinder liner using the piston ring reciprocating liner test rig. The scuffing resistance of the piston ring with the chromium-based ceramic composite coating (CKS), and that with the thermally sprayed nickel-chromium-molybdenum coating (NCM) is compared at different nominal pressures (40~100 MPa) and temperatures (180~250 °C). With the failure time as a criterion, the rank order is as follows: NCM/Fe > CKS/Fe. Before the scoring occurs at the interface of the piston ring and cylinder liner (PRCL), the cast iron liner enters into a “polish wear” stage, and iron-based adhesive materials begin to form on the piston ring surface. With the macroscopic adhesion formation, the plastic shearing cycle causes surface damages mainly due to abrasive effects for the CKS/Fe pairs and adhesive effects for the NCM/Fe pairs.

27 January 2019 in Metals
Verified
Journal Article
Open access
PDF file
WLWenhua Li
Wenhua Li
BYBaihong Yu
Baihong Yu
YLYutao Lv
Yutao Lv
YSYan Shen
Yan Shen
Ruoxuan HuangRuoxuan Huang
Ruoxuan Huang
Fengming DuFengming Du
Fengming Du
In order to investigate the friction and wear behavior between the nodular cast iron cylinder liner (Fe) and CuSn coated piston ring under heavy-duty conditions, piston rings with chromium(Cr) coating and CuSn-Cr coating were tested using the piston ring reciprocating liner test rig at the simulated working conditions of 56 MPa, 200 r/min, 190 °C. Compared with the Cr/Fe pair, the CuSn coating consumption of the CuSn-Cr/Fe pair made friction coefficient and cylinder wear loss decrease by 2.8% and 51.5%, respectively. Different size Sn patches worn from the CuSn coated piston ring were embedded into the cylinder liner surface based on the surface topography. This process was shown to reduce the surface roughness of a cylinder liner and form flatter plateau structures. Chemical elements analysis indicated that plateau structures on the cylinder liner surface matched with CuSn-Cr coated ring are helpful to promote the tribo-chemical reaction and generate the reactive products to protect the mutually contacted asperities.

23 February 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
YSYan Shen
Yan Shen
Zhixiang LiuZhixiang Liu
Zhixiang Liu
CXChuanfei Xing
Chuanfei Xing
QLQi Li
Qi Li
JFJunjing Fan
Junjing Fan
Mn+1AXn (MAX) phase materials present an attractive potential for friction reduction and wear resistance applications due to the ternary layered structure. This work was done to investigate how the combination of Ti2AlC and Ti3AlC2 MAX phase particles with zinc dialkyl dithiophosp (ZDDP) additives in the lubricant affected the tribo-surface by means of a reciprocating test rig with cyclic impact loading. The results indicated that the friction and wear properties of Ti3AlC2-containing lubricant were better than those of Ti2AlC-containing lubricant. The distinctive microstructure of worn surface caused by the Ti3AlC2 particles was characterized by the uniform distribution of many fine scratches, while the other was distributed with more peeling pits by the Ti2AlC particles. The tribo-chemical reaction of ZDDP involving Ti3AlC2 particles promoted a larger regional distribution of the tribofilm and the generation of short-chain phosphates. The synergistic effect of Ti3AlC2 particles and ZDDP additives led to excellent tribological properties.