Metal plate core‐based sandwich composites have the potential to revolutionize various industrial fields due to their mechanical strength and vibration damping. In this study, AZ91 (a magnesium alloy) and Al1050 (an aluminum alloy) metal core‐based sandwich composites of AZ91/carbon fiber‐epoxy, AZ91/glass fiber‐epoxy, Al1050/carbon fiber‐epoxy, and Al1050/glass fiber‐epoxy sandwich composites were manufactured. These composites' mechanical and dynamic properties were determined through tensile, three‐point bending, and vibration tests. AZ91‐reinforced carbon fiber composites exhibited a 28.8% higher tensile strength than glass fiber composites, while Al1050‐reinforced carbon fiber composites showed a 17.2% higher tensile strength performance than glass fiber composites. Moreover, AZ91 reinforcement led to composites with higher average flexural strength for both fibers. In vibration tests conducted under clamped and free‐free boundary conditions, the highest first natural frequency was observed in AZ91/carbon fiber samples, sparking further interest. Conversely, the highest first damping ratio was observed in Al1050/glass fiber specimens. In addition, the corrosion behavior of sandwiches was evaluated, and it was found that glass fiber provided better corrosion resistance than carbon fiber.Highlights: Sandwich composites comprising AZ91/Al1050 cores and carbon/glass fiber reinforced epoxy face sheets were manufactured. Galvanic corrosion effects were evaluated, and glass fiber was found to provide higher corrosion resistance. AZ91/carbon fiber sandwich showed 28.8% higher tensile strength than glass fiber. Vibration tests revealed the AZ91/carbon fiber sandwich had the highest first natural frequency. Al1050/glass fiber sandwich exhibited the highest first damping ratio.
Despite their extensive use in the automotive and aerospace industries, Mg and Mg alloys, which are light metals, exhibit low fatigue and tensile strength. In this study, transition metal-nitride (TMN) multilayer coatings (Ti+TiN+Ti+TiVN) were coated twice on AZ91 Mg alloy using a Confined Field Unbalanced Magnetron Sputtering (CFUBMS) system to increase fatigue and tensile strength. The structural properties of the films were analyzed by using X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive spectrometry (EDS) methods, and the mechanical properties were analyzed by rotating bending fatigue and tensile testing machines. Ti+TiN+Ti+TiVN multilayer nitride surface coatings on AZ91 Mg alloys showed a dense and columnar microstructure and according to XRD results (111) was the preferred orientation with the dominant peak. The fatigue limit value of the AZ91 base material was fixed at 60.46 MPa, while it increased to 68.48 MPa after being coated with multilayer nitride. Along with the multilayer nitride coating, the tensile strength increased from 169.98 MPa to 175.43 MPa. As a result, the multilayer hard nitride coating with low surface roughness, which fills the defects, notches, and voids on the surface of the AZ91 base material, increased the fatigue and tensile strength in parallel. Based on the outcomes of the research, the literature has been enriched with an innovative approach through the enhancement of fatigue and tensile strengths by applying a CFUBMS coating to lightweight metals and alloys, such as AZ91, especially in the transportation industry where lightness and dynamic load resistance are essential.
Powder-bed arc additive manufacturing (PBAAM) may reduce the cost of powder-bed metal additive manufacturing and enable thicker layers than laser powder bed fusion (LPBF), but melt-track stability limits are not well established. Here, 316L stainless steel powder (15–53 µm) was melted by a TIG-based arc in a custom powder-bed system while varying current, travel speed, layer thickness and hatch distance. Single tracks on an inclined bed (≈0–0.4 mm thickness) were used to identify continuity loss and melt-pool width, quantified from top-view images via width profiles, a gap-based continuity metric and the coefficient of variation. Parallel-track tests at 0.15, 0.20 and 0.25 mm layer thickness with hatch distances set to 25%, 50% and 75% of the measured melt-pool width assessed inter-track bonding and lack of fusion, and selected parameters were validated in five-layer builds. Higher current with low-to-moderate travel speeds produced wider, more stable melt pools on the inclined bed. Hatch ratios of 25–50% were the most effective for sustaining fusion in single layers and multi-layer builds, whereas 75% promoted unbonded regions and narrow-track morphologies. Overall, PBAAM can process substantially thicker layers with relatively simple equipment, but requires a narrow, carefully tuned window to balance continuity, fusion and heat accumulation.
25 September 2022 in Journal of Health Sciences and Medicine
Aim: Although primarily known as a respiratory system pathology, COVID-19 may cause various systems and cause serious complications including neuropsychiatric problems. These complications may be formulized as post-COVID syndrome. The current study aims to investigate prolonged cognitive, somatic and psychiatric effects of COVID-19. Material and Method: A total number of 120 COVID-19 survivors were compared with 120 health controls in means of three measures, which are Cognitive Failures Questionnaire (CFQ), Body Sensations Questionnaire (BSQ), Hospital Anxiety and Depression Scale (HADS) to assess cognitive difficulties, body perceptions and anxiety/depression. Results: Our findings show that COVID-19 survivors have reported significantly more cognitive difficulties, increased body sensations and higher levels of anxiety. The groups did not differ in means of depression scores. Further, the measures were significantly correlated with each other. Conclusion: This study reveal that COVID-19 survivors suffer from significant cognitive deficits in everyday activities, are significantly more sensitive to various body sensations and have increased anxiety levels. In discordance with the current literature, our findings showed that COVID-19 patients are not more depressed than healthy subjects. In summary, the current study showed that various neuropsychiatric complications may be an important part of prolonged effects of COVID-19.
FDM-printed polylactic acid (PLA) composites containing 5 and 10 wt% obsidian powder sourced from the Kars region of Eastern Anatolia (Turkey) were produced via twin-screw masterbatch extrusion and subsequent single-screw filament dilution. Mechanical (tensile, three-point flexure, notched Charpy impact, Shore D), physical (density), thermal (simultaneous TGA/DSC) and microstructural (macroscopic fractography and SEM at 100×–1000×) characterizations were performed on FDM-printed specimens. Young’s modulus rose monotonically by +9.0% at 5 wt% and +18.2% at 10 wt%, while ultimate tensile strength decreased by 12.4% and 17.3%, respectively. The flexural modulus increased by +15.2% at 5 wt% and plateaued at 10 wt% (+16.7%), whereas the flexural strength decreased by only 3.5% at 10 wt%, indicating that flexure-mode loading is markedly more tolerant of obsidian filler than axial tension. Shore D hardness rose by +2.11 points from 0 to 5 wt% with saturation thereafter. TGA showed a dual thermal effect: T5 and T10 dropped by 5–6 °C from 5 to 10 wt%, while the main decomposition rate decreased by ~46% and the decomposition interval widened from 9.7 to 23.5 °C, indicating a barrier/heat-shielding effect of dispersed silicate particles. SEM revealed a continuous ductile → transitional → brittle progression with increasing obsidian content; extended interfacial debonding lines at 10 wt% identified weak unmodified filler/matrix coupling as the principal performance-ceiling factor. Density measurements indicated a ~3–6% residual void fraction consistent with the inter-bead voids observed by SEM. To the authors’ knowledge, this is the first systematic study of obsidian as a reinforcing filler in PLA; the 5 wt% composition is identified as a strong candidate for esthetic, flexure-dominant, and low-load structural applications.
20 July 2026 in Journal of Adhesion Science and Technology
1. Additive manufacturing (AM) technologies have found increasingly widespread application in the aerospace, biomedical, automotive and consumer goods sectors over the past decade, owing to the adv...