Assanali Sultanov

Dr. Assanali Sultanov


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 February 2026 in Coatings
Verified
Journal Article
Open access
PDF file
KSKeiinbay Symaiyl
Keiinbay Symaiyl
KNKair Kh. Nussupov
Kair Kh. Nussupov
ASAssanali Sultanov
Assanali Sultanov
IZIlya V. Zhirkov
Ilya V. Zhirkov
NBNurzhan B. Beisenkhanov
Nurzhan B. Beisenkhanov
Alex A. VolinskyAlex A. Volinsky
Alex A. Volinsky
In this study, the diffusion barrier performance of TiN and SiC layers was investigated in Si/TiN/Cu, Si/TiN/SiC/Cu, and Si/SiC/TiN/Cu multilayer structures to address copper diffusion issues at silicon interfaces in microelectronics. Samples were annealed in argon at 500–800 °C for 30 min, and diffusion behavior was analyzed using X-ray diffraction (XRD) and sheet resistance measurements. The Cu3Si phase formed at 600 °C in the Si/TiN/Cu system, while no Cu3Si appeared in the Si/SiC/TiN/Cu system up to 700 °C, indicating improved stability. Complete copper diffusion occurred in all systems at 800 °C. Sheet resistance measurements corroborated the XRD findings, demonstrating that multilayer structures incorporating TiN and SiC significantly enhance thermal stability and suppress copper diffusion. Comparison of Si/SiC/TiN/Cu and Si/TiN/SiC/Cu stacks annealed at 700 °C revealed that the stability of TiN depends on layer sequence, with SiC effectively blocking Cu migration into TiN when placed adjacent to Cu. Structural and morphological properties of TiN films were also examined, confirming their suitability as diffusion barriers. Additionally, the feasibility of forming a low-resistivity TiSi2 layer through a single annealing step to create a TiSi2/TiN system was explored, highlighting potential applications in advanced device integration.

1 December 2023 in Physical Sciences and Technology
Verified
Journal Article
Open access
PDF file
KNKair Kh Nussupov
Kair Kh Nussupov
NBNurzhan B Beisenkhanov
Nurzhan B Beisenkhanov
AKAizhan Zh Kusainova
Aizhan Zh Kusainova
DSDarkhan S Shynybayev
Darkhan S Shynybayev
IZIlya V Zhirkov
Ilya V Zhirkov
ASAssanali Sultanov
Assanali Sultanov
Thin AZO films were synthesized using radio frequency magnetron sputtering method on the surface of polished silicon samples and glass slides. The sputtering power was varied in the range of 150–300 W with the step of 25W; deposition time was adjusted so that the film thickness remained equal to 70 nm. The rest of the deposition parameters: working pressure, temperature, and the substrate rotation rate, remained unchanged. The thickness and deposition rate of thin films were measured using X-ray reflectometry. The electrical properties (resistivity, Hall mobility and charge concentration) of thin films were measured by the Van Der Pauw method using the Hall effect. The transmission spectra of the films were measured in the wavelength range from 300 to 1100 nm. The average crystallite size was determined using X-ray diffraction spectra and the Scherrer equation. As a result, it was shown that AZO films synthesized at a power of 300 W have the best electrical and optical properties. At this power, the lowest resistivity value of 2.83×10-3 Ω∙cm and the maximum charge mobility of 9.6 cm2V-1sec-1 were achieved for films of the same thickness 70 nm. The decrease in the electrical resistivity of the films with increasing power is explained by more intense heating of the substrate during deposition, which leads to an improvement in the crystallinity of the film, and, as a consequence, to an increase in the mobility of charge carriers.