A test coupon coated with light calcareous tubeworm fouling was scanned, scaled and reproduced for wind-tunnel testing to determine the equivalent sand grain roughness ks. It was found that this surface had a ks = 0.325 mm, substantially less than the previously reported values for light calcareous fouling. This result was used to predict the drag on a fouled full scale ship. To achieve this, a modified method for predicting the total drag of a spatially developing turbulent boundary layer (TBL), such as that on the hull of a ship, is presented. The method numerically integrates the skin friction over the length of the boundary layer, assuming an analytical form for the mean velocity profile of the TBL. The velocity profile contains the roughness (fouling) information, such that the prediction requires only an input of ks, the free-stream velocity (ship speed), the kinematic viscosity and the length of the boundary layer (the hull length). Using the equivalent sandgrain roughness height determined from experiments, a FFG-7 Oliver Perry class frigate is predicted to experience a 23% increase in total resistance at cruise, if its hull is coated in light calcareous tubeworm fouling. A similarly fouled very large crude carrier would experience a 34% increase in total resistance at cruise.
The scale interactions occurring within a turbulent boundary layer are investigated in the presence of free-stream turbulence. The free-stream turbulence is generated by an active grid. The free stream is monitored by a single-component hot-wire probe, while a second probe is roved across the height of the boundary layer at the same streamwise location. Large-scale structures occurring in the free stream are shown to penetrate the boundary layer and increase the streamwise velocity fluctuations throughout. It is speculated that, depending on the extent of the penetration, i.e. based on the level of free-stream turbulence, the near-wall turbulence production peaks at different wall-normal locations than the expected location of $y^{+}\approx 15$ for a canonical turbulent boundary layer. It is shown that the large scales dominating the log region have a modulating effect on the small scales in the near-wall region; this effect becomes more significant with increasing turbulence in the free stream, i.e. similarly increasing $Re_{\unicode[STIX]{x1D706}_{0}}$ . This modulating interaction and its Reynolds-number trend have similarities with canonical turbulent boundary layers at high Reynolds numbers where the interaction between the large scales and the envelope of the small scales exhibits a pure amplitude modulation (Hutchins & Marusic,Phil. Trans. R. Soc. Lond.A, vol. 365 (1852), 2007, pp. 647–664; Mathiset al., J. Fluid Mech., vol. 628, 2009, pp. 311–337). This similarity has encouraging implications towards generalising scale interactions in turbulent boundary layers.
In this study, the development of a boundary layer past a change in surface roughness (from rough to smooth, $\text{R}\rightarrow \text{S}$ ) is examined. Measurements of the flow were made by hot wires, whereas the friction velocity was estimated by Preston tube measurements. By means of a diagnostic plot of the turbulence intensity, it is shown that above the internal layer the flow exhibits characteristics of a rough, wall-bounded flow, whereas near the wall the turbulence intensity is similar to that of an isolated smooth wall. Similarly, viscous scaling of the mean streamwise velocity shows an excessive wake region downstream of the $\text{R}\rightarrow \text{S}$ wall surface change that diminishes with the fetch from the surface change. Above the internal layer a second peak in the streamwise Reynolds stress was associated with the upstream rough-wall flow. Examination of the turbulent spectra revealed the presence of large-scale motions within this region that gradually diminish in strength with increasing distance from the change in surface roughness. The magnitude of the near-wall peak failed to collapse to that of a comparable smooth-wall boundary layer under viscous scaling, however, the wall-normal location of the peak appears to be at $y^{+}\approx 15$ at all downstream distances. A new mixed scaling is proposed for the near-wall peak based on the corrected wake deficit and the friction velocity. This shows the importance of outer region to the growth of near-wall peak in this non-equilibrium boundary layer.
It is a known phenomenon that some dielectric materials used to construct plasma actuators degrade during operation. However, the rate at which this process occurs, to what extent, as well as a method to monitor is yet to be established. In this experimental study, it is shown that electrical measurements can be used to monitor changes in the material of the plasma actuators. The procedure we introduce for monitoring the actuators follows from the work of Kriegseis, Grundmann, and Tropea [Kriegseis et al., J. Appl. Phys. 110, 013305 (2011)], who used Lissajous figures to measure actuator power consumption and capacitance. In the present study, we quantify changes in both the power consumption and capacitance of the actuators over long operating durations. It is shown that the increase in the effective capacitance of the actuator is related to degradation (thinning) of the dielectric layer, which is accompanied by an increase in actuator power consumption. For actuators constructed from layers of Kapton® polyimide tape, these changes are self-limiting. Although the polyimide film degrades relatively quickly, the underlying adhesive layer appears to remain intact. Over time, the effective capacitance was found to increase by up to 36%, 25%, and 11% for actuators constructed with 2, 3, and 4 layers of Kapton tape, respectively. A method is presented to prevent erosion of the Kapton dielectric layer using a coating of Polydimethylsiloxane oil. It is shown the application of this treatment can delay the onset of degradation of the Kapton dielectric material.