An ultracompact, cost-effective, and highly accurate fiber optic temperature sensor is proposed and demonstrated. The sensing head consists of Fabry-Perot microcavity formed by an internal mirror made of a thin titanium dioxide (TiO₂) film and a microscopic segment of single-mode fiber covered with Poly(dimethylsiloxane) (PDMS). Due to the high thermo-optic coefficient of PDMS the reflectance of the fiber-PDMS interface varies strongly with temperature which in turn modifies the amplitude of the interference pattern. To quantify the changes of the latter we monitored the visibility of the interference pattern and analyzed it by means of the fast Fourier transform. Our sensor exhibits linear response, high sensitivity, and response time of 14 seconds. We believe that the microscopic dimensions along with the performance of the sensor here presented makes it appealing for sensing temperature in PDMS microfluidic circuits or in biological applications.

An in-fiber Mach-Zehnder Interferometer (MZI), based on hollow core fiber (HCF), for measuring curvature is fabricated and experimentally demonstrated. The sensing part was fabricated by splicing a section of HCF between two sections of multimode fiber (MMF), and different HCF lengths were investigated in order to achieve the highest curvature sensitivity. These devices were tested in a transmission configuration using lead-in and lead-out single mode fibers (SMF). The sensor was attached to a steel sheet by using the polymer Polydimethylsiloxane (PDMS) for accurate control of the applied curvature. The modal analysis was carried out using a commercial software based on finite element method (FEM) and, by incorporating some of the experimental data, it was feasible to determine the two dominant modes that interfere in this sensor. The devices were characterized by measuring the fringe contrast variations due to the curvature changes. The interferometer fabricated with a HCF 2.5 mm in length HCF showed the highest curvature sensitivity, -17.28 ${\pm}$ 2.30 dB/m $^{-1}$ , in a range from 1.84 m $^{-1}$ to 2.94 m $^{-1}$ . Moreover, the sensor that exhibited a better performance was fabricated with a HCF length of 1 mm, combining the most extensive curvature range (from 0.95 m $^{-1}$ to 2.68 m $^{-1}$ ) and an adequate sensitivity (-11.80 ${\pm}$ 1.30 dB/m $^{-1}$ ). The analysis of the interferometric signal of this device in Fourier domain, allows us to establish a one to one relationship between the contrast and the curvature in a broader range (from 0 m $^{-1}$ to 2.94 m $^{-1}$ ). Moreover, the fringe contrast showed a very low dependency on temperature (from 30°C to 90 °C), showing that this device was not affected by temperate fluctuation.

A highly sensitive salinity sensor based on a two-core optical fiber is demonstrated for both high- and low-concentration regimes. Salinity of several aqueous solutions is measured in the ranges from 0 to 5 mol/L and from 0 to 1 mol/L with sensitivities of 14.0086 and 12.0484 nm/(mol/L), respectively. The achieved sensitivity is ~19 times higher than that recently reported for polymide-coated photonic crystal fibers.

Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.

In this paper, we propose and experimentally demonstrate a simple technique to enhance the curvature sensitivity of a bending fiber optic sensor based on anti-resonant reflecting optical waveguide (ARROW) guidance. The sensing structure is assembled by splicing a segment of capillary hollow-core fiber (CHCF) between two single-mode fibers (SMF), and the device is set on a steel sheet for measuring different curvatures. Without any surface treatment, the ARROW sensor exhibits a curvature sensitivity of 1.6 dB/m⁻¹ in a curvature range from 0 to 2.14 m⁻¹. By carefully coating half of the CHCF length with polydimethylsiloxane (PDMS), the curvature sensitivity of the ARROW sensor is enhanced to −5.62 dB/m⁻¹, as well as an increment in the curvature range (from 0 to 2.68 m⁻¹). Moreover, the covered device exhibits a low-temperature sensitivity (0.038 dB/°C), meaning that temperature fluctuations do not compromise the bending fiber optic sensor operation. The ARROW sensor fabricated with this technique has high sensitivity and a wide range for curvature measurements, with the advantage that the technique is cost-effective and easy to implement. All these features make this technique appealing for real sensing applications, such as structural health monitoring.