Microwave absorbers (MAs) play an important role in protecting sensitive electronic devices from electromagnetic (EM) interference by absorbing the energy of incoming waves and reducing unnecessary reflection or transmission. Here, we numerically and experimentally demonstrated two types of waveform-selective microwave metasurface absorbers (MMAs) with a single square-patch structure and a lumped nonlinear circuit. Our MMAs were designed to preferentially absorb signals at the same frequencies, including a higher-order mode. The proposed capacitor-type MMA was comprised of a single square-patch structure connected with a diode bridge containing a capacitor paired with a resistor in parallel, which could effectively absorb short pulses at two distinct frequencies. Similarly, the proposed inductor-type MMA was comprised of the same square-patch structure, except for the internal circuit replaced with an inductor paired with a resistor in series, which could effectively absorb continuous waves (CWs) at the same two frequencies. The effects of the parameters of lumped circuit components (resistor, capacitor, and inductor) and geometrical parameters on the waveform-selective absorptance of these two types of MMAs for normal incident short pulses and CWs were systemically studied. Both the simulation and experimental results showed selective absorption for specific waveforms at the same two frequencies, including a high-order mode. Thus, the waveform-selective MMAs can provide a wide application range, such as EM shielding, detection, sensing, and wireless communications.
Wireless communications and sensing have notably advanced thanks to the recent developments in both software and hardware. Although various modulation schemes have been proposed to efficiently use the limited frequency resources by exploiting several degrees of freedom, antenna performance is essentially governed by frequency only. Here, we present an antenna design concept based on metasurfaces to manipulate antenna performances in response to the time width of electromagnetic pulses. We numerically and experimentally show that by using a proper set of spatially arranged metasurfaces loaded with lumped circuits, ordinary omnidirectional antennas can be reconfigured by the incident pulse width to exhibit directional characteristics varying over hundreds of milliseconds or billions of cycles, far beyond conventional performance. We demonstrate that the proposed concept can be applied for sensing, selective reception under simultaneous incidence and mutual communications as the first step to expand existing frequency resources based on pulse width.
Metasurfaces can implement a wide variety of wave-manipulation functions with sub-wavelength layers. They are typically created from resonant elements, thus their refraction properties depend strongly on frequency. The resulting chromatic aberration is undesirable for most applications, motivating recent efforts in the development of achromatic metasurfaces. However, it remains unclear whether there are any physical limits on the achievable operating bandwidth of achromatic metasurfaces. Here we address this question, considering a common microwave metasurface geometry based on three metallic layers, separated by dielectric substrates. Since each of these metallic layers is modeled as an impedance, we apply Foster’s reactance theorem to determine the bandwidth over which they are physically realizable using passive, causal and lossless structures. We derive limits for the bandwidth and total size of the metasurface, showing that there is a trade-off between these two parameters. A higher angle of refraction, corresponding to a larger numerical aperture for a lens, further limits the realizable bandwidth. We consider both Huygens’ and Omega-bianisotropic metasurface types, and show that the limit is more severe for bianisotropic metasurfaces, making them less suitable for broadband achromatic designs.
6 October 2020 in Journal of Physics D: Applied Physics
Metasurfaces have emerged as a promising technology for the manipulation of electromagnetic waves within a thin layer. In planar ultrathin metasurfaces, there exist rigorous design methods, based on the equivalent surface impedance of patterned metallic layers on dielectric substrates. In this work, we derive a limit on bandwidth achievable in these metasurfaces, based on constraints that their meta-atoms should be passive, causal and lossless and that they should obey the time-bandwidth product rules of a single resonance structure. The results show that in addition to elementary design parameters involving variation of the surface impedance, the bandwidth is critically limited by the dielectric substrate thickness and permittivity. We then propose a synthesis method for broadband ultrathin metasurfaces, based on an LC resonance fit of the required surface impedance and experimentally verify a broadband dispersive structure at millimeter-wave frequencies. This results in a bandwidth enhancement of over 90%, relative to a reference metasurface created with the narrowband design process.
Wave phenomena can be artificially engineered by scattering from metasurfaces, which aids in the design of radio-frequency and optical devices for wireless communication, sensing, imaging, wireless power transfer and bio/medical applications. Scattering responses vary with changing frequency; conversely, they remain unchanged at a constant frequency, which has been a long-standing limitation in the design of devices leveraging wave scattering phenomena. Here, we present metasurfaces that can scatter incident waves according to two variables—the frequency and pulse width—in multiple bands. Significantly, these scattering profiles are characterized by how the frequencies are used in different time windows due to transient circuits. In particular, by using more than one frequency with coupled transient circuits, we demonstrate variable scattering profiles in response to unique frequency sequences, which can break a conventional linear frequency concept and markedly increase the available frequency channels in accordance with a factorial number of frequencies used. Our proposed concept, which is analogous to frequency hopping in wireless communication, advances wave engineering in electromagnetics and related fields.