Single-crystal fibers of ruby (Cr/sup 3+/:Al/sub 2/O/sub 3/) with approximately 0.1 wt.% Cr/sup 3+/ have been produced by the laser heated pedestal growth (LHPG) technique. The fluorescence emissions of the R/sub 1/ and R/sub 2/ lines were studied as functions of temperature and strain. Fluorescence decay lifetime measurements indicate that these fibers may be suitable for thermometric applications up to 973 K while strain measurements show only a very weak dependence. Similarly, characterization of the R-line shifts also show a weak strain sensitivity and an appreciably larger change with temperature. One fiber sample has been tested to destruction to demonstrate this weak strain dependence. Single-crystal ruby fibers are, thus, found to be potential candidates for dedicated temperature sensing from room temperature to /spl sim/923 K.
An innovative signal processing method based on custom-made wavelet transform (WT) is presented for robust detection of fringes contained in the interferometric signal of self-mixing (SM) laser diode sensors. It enables the measurement of arbitrarily-shaped vibrations even in the corruptive presence of speckle. Our algorithm is based on the pattern recognition capability of bespoke WTs for detecting SM fringes. Once the fringes have been correctly detected, phase unwrapping methods can be applied to retrieve the complete instantaneous phase of the SM signals. Here, the novelty consists in using two distinct mother wavelets Ψ r (t) and Ψ d (t) specifically designed to distinguish SM patterns as well as the displacement direction. The peaks, i.e. the maxima modulus of WT, then allow the detection of the fringes.
We propose and develop a comprehensive model for estimating the refractive index (RI) response over three potential sensing zones in a multimode fiber. The model has been developed based on a combined ray optics, Gaussian beam, and wave optics analysis coupled to the consideration of the injected interrogating lightwave characteristics and validated experimentally through the realization of three sensors with different lengths of stripped cladding sections as the sensing region. The experimental results highly corroborate and validate the simulation output from the model for the three RI sensing zones. The sensors can be employed over a very wide dynamic RI range from 1.316 to over 1.608 at a wavelength of 1550 nm, with the best resolution of 2.2406 × 10−5 RI unit (RIU) obtained in Zone II for a 1-cm sensor length.
1 September 2002 in Sensors and Actuators A: Physical
Tilt fluctuations can potentially reflect the response of hydrosystems to important rainfall. In this context, long baseline tiltmeters have been installed in an underground tunnel penetrating the Fontaine de Vaucluse karst to study the medium deformation related to solicitations exerted by water infiltrating the hydrosystem. The instruments monitor the tilt as well as its spatial variation. Northward tilts reaching a 1 μrad amplitude are observed consecutively to rainfalls. The tilt amplitude is highly correlated with the Fontaine de Vaucluse outlet flow fluctuations. The measured tilt signal is also relatively homogeneous over a 150 m length. Different types of structure likely to produce such observations are tested in order to identify their location with respect to the tiltmeters, their dimension as well as the amount of water level variation in the structure. Following rainfalls, the infiltration of water modifies the pore pressure, inducing a medium deformation. The hypothesis of a homogeneous surface loading on the Vaucluse plateau is first refuted since the related tilt is much lower than the one measured. The water supplied by rainfalls has to accumulate in discontinuities in order to generate a higher tilt. So, the deformation related to a pressure exerted on a fracture filled by water is assessed. A first study reveals the interest of the tilt homogeneity information that constrains strongly the fracture properties. Thus, the fracture must be located at a distance more than a few hundred metres from the tiltmeters in order to produce a tilt homogeneous in space. If the fracture is initially dry, it must also be filled on a height higher than 150 m consecutive to a rainfall in order to generate a tilt amplitude in the same magnitude as the one measured. Then, we explore the influence of water level variations on the tilt produced by a fracture located at the interface between the saturated and unsaturated zones, which are thereby permanently flooded. Since several parameters of that model satisfactorily explain the field observations, we discuss how simultaneous geodetical observations could provide complementary information that would further constrain the geometry of the structure at the origin of the medium deformation.