The fatigue fracture of a drillstring could cause drilling disturbances and some negative impacts (e.g., economic loss) will be brought when restoring the drillstring to functionality. In order to evaluate the effects of the fatigue damage of the drillstring during drilling, a new apparatus, which could monitor the load level in real-time, was built to perform the four-point bending fatigue test on 35CrMo steel, a typical material of drillstrings. Such an apparatus is based on metal magnetic memory (MMM) technology and can acquire the tangential and normal components of MMM signals. Based on the analysis of the change of surface morphology and MMM signals, it was concluded that the variation of MMM signals could be divided into four stages, which are used to accurately describe the fatigue damage process of the drillstring. Additionally, the MMM signal characteristics are introduced to especially evaluate the fatigue damage of the drillstring, including crack initiation. Furthermore, the scanning electron microscopy (SEM) results demonstrated that morphologies of fatigue fracture were related to the variation of MMM signals. Linear fitting results indicated that fatigue crack length had a good linear relationship with the characteristics, so it is feasible to monitor fatigue damage and predict the residual life of a drillstring by using MMM technology.
The magnitude and distribution of contact stress on the metal-to-metal seal interface of premium connection has been confirmed as a direct factor of the sealing integrity. In this study, the method of evaluating sealability by measuring contact stress on metal-to-metal seals with the ultrasonic phased array is investigated. A loading system and ultrasonic phased array measurement system of cone-cone contact samples were created. The recommended detection method is focusing -deflection, and the time compensation method is suggested to extract the reflected wave peak of the sealing surface. The experiments show that the reflected wave peak declines with the rise of the axial load, with the big end showing the most noticeable reduction. The shift in the reflected wave peak also reflects the axial movement of the contact interface. The contact stress is calculated according to the reflection coefficient and compared with the simulation results. The distribution trend of contact stress is consistent. The sealing index measurement error is less than 15%, and the measurement error is decreased with the decrease of the sealing surface angle. Then, the nephogram of contact stress distribution on the sealing surface is formed to visualize the contact stress, which takes on great significance in engineering.
Gas sensors based on metal oxide semiconductors (MOS) have attracted significant attention in monitoring of methane emission and leakage monitoring due to their high sensitivity, fast response time, simple structure and low cost. However, the high power consumption caused by long-term high-temperature operation of MOS sensors restricts their application in mobile and portable devices. In this study, MOF-derived Co3O4 dodecahedrons for low-concentration methane detection at room temperature was prepared using Zeolitic Imidazolate Framework-67 (ZIF-67) as a template and with various calcination temperatures. Among them, the Co3O4-350 calcined at 350 °C exhibited the optimal CH4 sensing performance at room temperature, with a response of Rg/Ra = 1.53 to 2000 ppm CH4. This enhanced gas sensing performance is attributed to the highest Co3+ proportions and the largest specific surface area in Co3O4-350 nanomaterials, which provided more active sites for gas adsorption and reaction. To address the challenge of slow response speed and irrecoverability during CH4 detection at room temperature, the Co3O4 nanomaterials were printed onto a micro-heater plate (MHP) to form a MEMS gas sensor. By introducing a pulse heating mode to the MEMS sensor, the response and recovery time were significantly reduced to 26 s and 21 s, respectively. This enhancement improves both the efficiency and reliability of the MEMS gas sensor for early-stage detection of CH4 leaks in various industrial applications.
In terms of the structural health inspection of storage tanks by ultrasonic guided wave technology, many scholars are currently focusing on the tanks’ floor and walls, while little research has been conducted on storage tank roofs. However, the roof of a storage tank is prone to corrosion because of its complex structure and unique working environment. For this purpose, this paper proposes a reflection/transmission signal amplitude ratio (RTAR) coefficient method for corrosion depth assessment. We studied the relationship between the RTAR coefficient, the corrosion depth, and the guided wave frequency to establish a depth assessment model. More importantly, unlike the traditional reflection coefficient method, the characteristics of guided wave signals, including the propagation and attenuation, are introduced in this model for accurate assessment. To eliminate the interference of residual vibration and improve the detection accuracy of defects, we built a corrosion detection system by using piezoelectric sensors and carried out field tests to verify the performance of the proposed method. We demonstrate that corrosion defects with a minimum depth of 0.2 mm can be quantitatively evaluated.
Drill pipe threads are susceptible to fatigue cracking under complex downhole loads, posing significant risks to drilling safety. Although metal magnetic memory (MMM) testing enables efficient nondestructive evaluation, its practical utility is often compromised by interference from material magnetization and lift-off distance. To overcome this limitation, we introduce a novel damage assessment method based on the area peak-to-mean ratio (APMR) of magnetic signals. This feature is specifically designed to suppress external disturbances while retaining sensitivity to stress-induced magnetic anomalies. Finite element analysis was performed to elucidate the magneto-mechanical coupling behavior at defective thread roots. Subsequently, MMM signals were acquired from drill pipe threads under varying inspection conditions using a custom-built scanning system equipped with 16 tunneling magnetoresistance (TMR) sensors. Multiple features, including APMR, were extracted and evaluated across various machine learning classifiers. The gradient boosting machine (GBM) achieved superior performance, yielding an accuracy of 0.9861 and a recall of 1.0000 on the test set—outperforming all other models. This work presents an effective automated approach for drill pipe thread damage evaluation, contributing to enhanced reliability and safety in drilling operations.
Stable leak localization in CCUS injection wellbores remains difficult under strong background noise. This study proposes a leak localization method based on autocorrelation time delay features of leakage acoustic signals. Considering the generation of confined leakage noise and its waveguide propagation in the wellbore, a time delay relationship between the direct acoustic component and the bottom-reflected echo is established, and an integrated workflow is developed for signal preprocessing, normalized autocorrelation analysis, feature extraction, and location inversion. Experimental results show that the dominant autocorrelation time delay feature remains stable under varying leakage conditions, while leak position changes produce distinguishable peak–valley patterns. The proposed method achieves high localization accuracy, with absolute errors of 0.018–0.046 m and relative errors of 0.76–1.93% under the tested conditions. A field application in a CO2 injection well further demonstrates its practical feasibility. Overall, the method provides a stable and effective approach for leak localization in CCUS injection wellbores and shows potential for engineering applications in noisy environments.