Boron is a promising fuel, but its oxide layer impedes combustion. Alloying boron with other high-energy metals can significantly enhance its combustion performance. In this study, we sintered highly reactive lithium-containing Mg-Al-Li-B alloys using magnesium, aluminum–lithium alloy, and boron powder as raw materials. The effects of sintering temperature and holding time on the microstructure were investigated, and the combustion heat value and oxidation resistance of the alloy were tested. Results indicate that sintering temperature significantly influences phase formation: increasing temperature boosts phase content while reducing metallic phases, with 1100 °C identified as the optimal sintering temperature. Holding time had no discernible impact on the phase composition or combustion heat value of the sintered alloy. Alloying enhances material density, thereby increasing volumetric heat value. Thermal oxidation performance tests demonstrate that Li addition significantly lowers the alloy’s oxidation reaction temperature and activation energy, enhancing its reactivity. This high-heat-value, highly reactive alloy holds significant potential for application in pyrotechnics and propellants.
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.
Refractory High-entropy alloys (RHEAs) exhibit a unique combination of exceptional properties, making them suitable for extreme environments, owing to their multi-principal element effects. In this study, a novel Nb35Zr20Ti20W25 refractory high-entropy alloy was systematically investigated. The mechanical behavior of the alloy under various strain rates and temperatures was characterized using a universal testing machine and a split Hopkinson pressure bar (SHPB) system. Its parameters of Johnson-Cook constitutive model were calibrated, and the accuracy of the constitutive parameters was verified by numerical simulation using the software of ABAQUS. The results indicate that the Nb35Zr20Ti20W25 high-entropy alloy, featuring a dual-phase (BCC1 + BCC2) structure, exhibits excellent strength, relatively high density, and good ductility. As the strain rate increased from 10-4 s-1 to 5020 s-1, the yield strength increased from 1559.14 MPa to 2620.92 MPa, demonstrating a pronounced strain-rate strengthening effect. The stress-strain curve derived from the constitutive model was highly consistent with the experimental results. This study may provide a reference for the determination of the parameters of J-C constitutive model and the numerical simulation of Nb35Zr20Ti20W25 refractory high-entropy alloy.
23 October 2026 in Journal of Alloys and Compounds