Energetic structural materials play an important role in improving the damage performance of future weapons. To improve the energy-releasing behavior, Al0.5NbZrTi1.5Ta0.8Cex high-entropy alloys were prepared by vacuum-arc melting. The results showed the presence of BCC and FCC phases in the alloy with dendritic-morphology-element segregation and there were significant dislocations in the alloys. The current study focused on the effects of cerium content on the dynamic compressive mechanical and energetic characteristics. Cerium doping enhanced the energy-releasing characteristics of high-entropy alloys. The severity of the reaction increased with the increase in the cerium content, while the dynamic compressive strength generally decreased with the increase in cerium content. The Al0.5NbZrTi1.5Ta0.8Ce0.25 showed excellent mechanical and energy-releasing characteristics. The ballistic experiments indicated that Al0.5NbZrTi1.5Ta0.8Ce0.25 can penetrate 6-millimeter A3 plates and ignite the cotton behind the target at a velocity of 729 m/s, making it an ideal energetic structural material.
Boron and its alloys have been explored a lot and it is expected that they can replace pure aluminum powder in the energetic formulation of active materials. MgB2 compounds were prepared and characterized by a combination of mechanical alloying and heat treatment. The ignition and combustion of boron–magnesium alloys were studied with the ignition wire method and laser ignition infrared temperature measurement. The results show that MgB2 has good ignition characteristics with maximum ignition temperatures obtained by the two various methods of 1292 K and 1293 K, respectively. Compared with boron, the ignition temperature of MgB2 is greatly reduced after alloying. The ignition reaction of MgB2 mainly occurs on the surface and the ignition process has two stages. In the initial stage of ignition, the large flame morphology and combustion state are close to the combustion with gaseous Mg, whereas the subsequent combustion process is close to the combustion process of B. Compared with boron, the ignition temperature of MgB2 is greatly reduced which suggests that MgB2 may be used in gunpowder, propellant, explosives, and pyrotechnics due to its improved ignition performance.
Boron is a promising fuel, but its oxide layer impedes combustion. Alloying boron with other high-energy metals can significantly enhance its combustion performance. In this study, we sintered highly reactive lithium-containing Mg-Al-Li-B alloys using magnesium, aluminum–lithium alloy, and boron powder as raw materials. The effects of sintering temperature and holding time on the microstructure were investigated, and the combustion heat value and oxidation resistance of the alloy were tested. Results indicate that sintering temperature significantly influences phase formation: increasing temperature boosts phase content while reducing metallic phases, with 1100 °C identified as the optimal sintering temperature. Holding time had no discernible impact on the phase composition or combustion heat value of the sintered alloy. Alloying enhances material density, thereby increasing volumetric heat value. Thermal oxidation performance tests demonstrate that Li addition significantly lowers the alloy’s oxidation reaction temperature and activation energy, enhancing its reactivity. This high-heat-value, highly reactive alloy holds significant potential for application in pyrotechnics and propellants.
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.