To produce lift on the wing of the aircraft, pressure distribution on the upper surface of the wing must be lower than the pressure on the lower of the wing. This can be done by making the air passage on the upper surface is longer than that on the bottom surface, or making the wing’s relative angle to the direction of the incoming stream of air. Air will tend to flow from areas with high pressure to areas with low pressure. The pressure difference between lower surface of the wing higher than the top surface of the wing also results in the occurrence of this airflow. The place that allows for the occurrence of “leakage” of this air is at the tip of the wing. The flow from lower surface to the upper upper surface of the wings produces a vortex flow similar to a small tornado known as wingtip vortices. This whirl causes the air tend to flow downward on the wing area, and referred to as the term downwash. One modification on the aircraft wing to reduce the impact of the vortex tip is the use of the winglet on the tip of the aircraft wing. This has been widely applied to the latest commercial aircraft to improve the efficiency of the aircraft. The numerical study was done using CFD software with 3D geometry configuration. The geometry of the specimen is airplane wing Eppler 562 with chord length of 0.036 m, swept angle 0° and modification of winglet type rearward wingtip fence winglet with cant angle of 75°. The airflow with velocity at the inlet of 10 m/s. The turbulent modeling is k-ω SST. Present study uses hybrid mesh with boundary layer mesh method. From the simulation results it is shown that there is an increase in lift coefficient (CL) and an increase in drag coefficient (CD) along with the increase of angle of attack. In rearward wingtip fence with cant angle 0° produce CL/CD better than cant angle 75° and plain wing. Rearward wingtip fence shows optimum performance of α = 8° settings compared to plain wing.
Wings are one of the aircraft components that play an important role in generating lift. One of the important factors affecting lift on the wing is the aspect ratio of the wing. The theory shows that the use of wings with infinite span length (infinite wing) is the most ideal wing design, but in fact it is impossible to make wings of infinite length. Therefore the wing’s length is limited and made with dimensions proportional to the fuselage length of the aircraft. The span length of the aircraft is limited, making a three-dimensional separation on the wing tip section which will form a secondary flow, where this flow gives loss on the performance of the aircraft as it reduces the effective area of the wing and increase the wing drag. One modification on the aircraft wing to reduce the impact of the vortex tip is the use of the winglet on the tip portion of the wing. This has been widely applied to the latest commercial aircraft to improve the efficiency of the aircraft and UAV (Unmanned Aerial Vehicle). The study using numerical simulation was done with simulation software with 3D geometric configuration. The geometry of the model is UAV wing Eppler 562 with chord length of 0.36 m, swept angle 0° and modification of whitcomb winglet with cant angle 90°. The was performed at inlet airflow of 10 m / s and the pressure at the outlet was 0 Pa (gage). The turbulent modeling used is k-ω SST. Discrete method is hybrid mesh with boundary layer mesh method. The results of flow visualization show that withcomb winglet can improve wing performance effectively at high angles of attack, especially at angle α = 8° and α = 10°, which CL/CD higher than airfoil without winglet. The rearward wingtip fence effective CL/CD is higher than airfoil without winglet after angle α = 10°.
Airduct system is not only a straight pipe, but there are also piping fittings/accessories such as 90° elbows. These pipe accessories work so air ducts can be installed as needed. However, the use of these piping accessories causes an increase in pressure drop due to friction loss, separation loss and secondary flow that occurs after the flow passes through the fittings. There is a considerable pressure drop on the ducting system, then the fluid flow will suffer a considerable energy loss as well. A method to reduce the pressure drop that occurs in the 90° elbow is by adding an inlet disturbance body (IDB). This study was conducted numerically and experimentally on a square duct with hydraulic diameter Dh = 125 mm and curvature ratio R/Dh = 1.5. Inlet disturbance body (IDB) is placed at the inner upstream side of the duct before the 90° inlet elbow with variation on distance l/Dh = 0.1 – 0.5, constant gap g/d = 0.2 and d/Dh = 0.1. Reynolds number (ReDh) is 3.97 × 104 < ReDh < 13.5 × 104. The turbulence model is k-ɛ realizable. From this research it can be obtained information that the use of IDB effectively recovers flows process and overcomes the negative effect of the secondary flow. IDB placement of the channel with distance l/Dh = 0.1 is the most effective distance to reduce pressure drop with decrease of 17.68%. While IDB with distance variation l/Dh = 0.5 has the highest pressure drop.
The ducting system is made up of 90° elbows and a few other fittings and accessories in addition to straight ducts. The friction loss, separation loss, and secondary flow loss are the main causes of the pressure decrease in an elbow, and they all increase with the presence of elbows. Utilizing too much energy to propel the flow is a cost associated with pressure loss. The aim of this research is to investigate turbulent flow via 90° square elbows and a square-sectioned duct through experimental methods by adding a circular turbulator (CT) close to the elbow wall's inner radius. The Reynolds numbers (ReDh) used in this research are 1.6×104, 4.8×104, and 9.5×104, with average flow velocities of 2 m/s, 6 m/s, and 12 m/s. Circular turbulators are added to the inner walls with angular positions (α) of 5°, 10°, 15°, and 20°. The results showed that the turbulence intensity increased toward the inner radius wall of the elbow in ducting with CT. For this study, the flow within the ducting with the CT is generally more turbulent than the flow inside the ducting without the CT. By including CT, it was possible to reduce the overall pressure loss in ducting with an elbow. The pressure reduction at two ReDh values (1.6×104 and 4.8×104) was only lessened by CT positioned at α=10°, 15°, and 20° out of the four CT placements. Conversely, CT positioned at α=5° can only effectively mitigate pressure decrease at ReDh=1.6×104. CT installation cannot lessen the pressure drop that happens in the ducting at a value of ReDh=9.5×104. CT placement at the three α values often helps to lower the pressure drop in the ducting. Using the CT, positioned at α=15°, is the greatest strategy to reduce the overall pressure decrease