In this work, an improved wet bonding method was developed for strengthening of fiber-reinforced polymer. A self-made roughened carbon fiber–reinforced polymer sheet (hereinafter referred to as RFRP sheet) was externally attached to the surface layer of a nano-kaolin-modified concrete test piece to form an RFRP–concrete wet-bonded test piece. Then, the pull-off bond test and the single shear test were performed on 32 and 30 test pieces, respectively. The performance of the wet bonding interface of RFRP–concrete in the normal and tangential directions was investigated by changing the length of glass fiber cellosilk in RFRP bonding resin, the diameter of RFRP porous pelelith rock, and the ratio of nano-kaolin. In addition, by comparing the scanning electron microscopy images of untreated fiber-reinforced polymer sheet and the concrete block without nano-kaolin, the mechanism of the adhesion enhancement of the RFRP–concrete interface was explained. The results show that the differentiation between fiber-reinforced polymer–concrete wet bonding failure and RFRP–concrete wet bonding failure was mainly based on the large-scale concrete with peeled off concrete surface. RFRP effectively enhanced the wet adhesion performance of the interface with concrete in both normal and tangential directions. The interface bonding ability increased by 900% and 42%, respectively, compared with the control test pieces. The diameter of pelelith rock was found to be the most important factor affecting the shear wet bonding performance of the RFRP–concrete interface. The second important factor was the ratio of nano-kaolin. The optimum conditions for the best tangential anti-peeling ability of the RFRP–concrete structure were found to be the addition of 5-mm-diameter pelelith stone, 3% nano-kaolin, and glass cellosilk of 89 mm length. When the RFRP and the concrete were wet-bonded, the uncured cement mortar effectively filled the holes of the original pelelith rock and acted as a mechanical lock, thereby increasing the bonding stress.
Over the past few decades, ultrahigh-performance concrete (UHPC) has been widely studied and applied because of its outstanding mechanical properties, such as its high strength and notable durability. However, because of its high cost and easy shrinkage cracking during early pouring in mass concrete construction, to reduce the cost of UHPC and reduce the cracks caused by early pouring, volcanic stone was used as a new type of UHPC coarse aggregate, while metakaolin (MK) was added to the system at the same time, and then two parameters, namely the volcanic rock particle size group and the MK dispersion ratio, were set. Scanning electron microscopy (SEM), X-ray diffraction (XRD) and thermogravimetric (TG) microanalysis methods were used to reveal the influence of changes in the material microstructure, phase composition, material composition and crystallinity of the mineral composition on the compressive properties of the UHPC cubes. The results show that the mechanical “lock-in effect” of the structure formed by the volcanic rock holes and mortar can effectively improve the shear resistance of the UHPC–volcanic rock interface, and the compressive strength of the UHPC cubes increases with the volcanic stone’s particle size. When the MK dispersion ratio is less than 4%, the cube compressive strength of the UHPC and the contents of CaCO3 crystals, C-S-H gel and travertine in the UHPC increase with an increasing MK dispersion ratio. At an age of 28 days, compared with the addition of 1% MK, the addition of 4% MK increases the production of C-S-H gel and travertine in the UHPC matrix by 24.82%. When the MK dispersion ratio is 4%, the crystallinity values of the C-S-H gel, travertine and limestone in the UHPC are greater. Adding MK at a 4% dispersion ratio can promote the crystallization of limestone into a large amount of calcite, which can increase the strength of UHPC. On the one hand, the addition of volcanic coarse aggregate results in the retention of more free water and bound water; on the other hand, it also makes it difficult to crystallize CaCO3. The combined action of MK at a 4% dispersion ratio and volcanic rock significantly inhibits CaCO3 crystallization.
19 July 2018 in IOP Conference Series: Materials Science and Engineering
The single test is carried out on totally 54 concrete samples with 6 different interface-roughness conditions, as to delve into the influence of concrete surface roughness on the concrete-FRP interface. Accordingly the closed-form solution based on the compressive strength and interface roughness parameters of concrete is acquired. As the research result indicates, the extremum and extreme point exist in terms of influence of concrete surface roughness on fracture energy, the model acquired in line with the test data is appropriately applicable under the condition 0.34≤ fi ≤0.56, and such model is overall applicable under the concrete strength of 30MPa≤ fc0 ≤50MPa. The model proposed hereof in this paper is superior to the existing models, as not only the significant contribution made by concrete strength to fracture energy is considered, but the influence of concrete surface roughness on interface is highlighted.
14 January 2023 in Advances in Materials Science and Engineering
As an effective method of strengthening concrete in the marine environment, wet bonding has maintained an efficient application mode for many years. At present, research on the wet bonding behavior of UHPC is very rare, so in order to investigate the interfacial bonding performance between basalt fiber-reinforced plastic (BFRP) mesh cloth and ultra-high performance concrete (UHPC) under wet bonding conditions, forty-eight BFRP-UHPC specimens were carried out to investigate the influence of dry/wet bonding type, mesh depth, and mesh thickness on the interfacial bonding performance between BFRP and UHPC, and the failure mechanism of the BFRP-UHPC interface was revealed by SEM detection. The test results show that the interfacial wet bonding performance between BFRP and UHPC is better than that of the dry bonding process. With the increasing thickness of BFRP mesh, the interfacial bonding stress of dry and wet bonding shows the opposite trend, respectively. The fiber interlayer structure is the weak link of BFRP; with the increase in mesh depth, the bonding normal stress decreases gradually. When the mesh depth of wet-bonded BFRP is 5 mm, the reinforcement effect is the best, the maximum increase of interfacial bonding stress is 74%, and the tensile strength ratio is as high as 1.74. Compared with the traditional FRP reinforced construction without fiber mesh, the BFRP mesh structure can greatly improve the wet bonding performance, which can provide a theoretical and experimental basis for the design and construction of UHPC wet bonded with BFRP reinforcement engineering. Due to the form and distribution direction of steel fiber, a mechanical occluding effect will be generated at the BFRP mesh, so these two factors are very valuable for this wet bonding research field, for which the related work needs to further proceed.
Carbon fibre reinforced polymer (CFRP) are widely used in bridge reinforcement projects. However, delamination at the CFRP-concrete interface caused by frequent fires significantly impacts structural safety, severely restricting the further and extensive development of CFRP in bridge engineering. In this paper, the sand filling method is used to quantitatively evaluate the roughness of the concrete beam's surface, and the interfacial normal and tangential bonding stresses between CFRPs and concrete after exposure to elevated temperatures were investigated. The strength grade of the concrete, concrete surface roughness and temperature were analysed to explore the behaviour of the CFRP composites. First, before the CFRP sheets were pasted, the concrete interfacial roughness was quantitatively evaluated, and 135 CFRP-concrete interfacial bonding tests were carried out. Then, two bonding models based on an elevated temperature field were proposed. Finally, the interfacial bonding failure mechanism was analysed by scanning electron microscope (SEM). The research results showed that the concrete surface roughness more significantly affects the interfacial bonding stress than does the strength grade of the concrete. The interfacial separation between CFRPs and epoxy resin occurs at 110 °C, and the glass transition temperature (Tg) is the critical factor determining the decrease in the bonding performance of CFRP composites. The two models proposed in this study exhibit high prediction accuracy and certain safety reserves and are applicable to the prediction of CFRP reinforcement design and construction after exposure to high temperatures. These models also have additional potential applications.
The durability of the carbon fiber-reinforced polymer (CFRP)–concrete interface is a critical indicator for assessing the service life of composite structures in cold regions. This study systematically investigates the normal bond behavior under coupled deicing salt and freeze–thaw cycles through single-sided salt-frost tests on 126 specimens. The influence of surface roughness, number of freeze–thaw cycles, concrete strength grade, and CFRP material type was systematically evaluated. The results demonstrate that bond behavior is positively correlated with surface roughness, with the f2 interface exhibiting optimal performance and increasing the ultimate capacity by up to 76.61% compared to the smooth interface. CFRP cloth showed superior bond retention compared to CFRP plates, which experienced a bond strength loss rate up to 26.90% higher than cloth specimens after six cycles. A critical performance threshold was identified between six and eight cycles, where the failure mode transitioned from cohesive adhesive failure to brittle interfacial debonding. Concrete matrix strength had a negligible effect compared to the dominant environmental damage. A two-parameter prediction model based on cycle count and roughness was established with high accuracy. SEM analysis confirmed that epoxy resin cracking, fiber–matrix debonding, and microcrack propagation in the concrete surface layer were the fundamental causes of macroscopic mechanical degradation. These findings provide a theoretical foundation for optimizing interface treatment and predicting the structural integrity of CFRP-strengthened systems in salt-frost regions.