Electrostatic spraying is considered an effective means to improve the efficacy of pesticide application and reduce pesticide consumption. However, the effectiveness of electrostatic spraying needs further validation in greenhouse environments, especially in long-range air-assisted spraying scenarios. A waist-shaped charging device has been improved to obtain a maximum charge-to-mass ratio of 4.4 mC/kg at an applied voltage of 6 kV in a laboratory setting, representing an increase of approximately 84.9% compared to a commercial circular charging electrode with a fan-shaped nozzle. A comparative air-assisted spray test between electrostatic deactivation (EDAS) and electrostatic activation (EAAS) was conducted on greenhouse tomato crops using a single hanging track autonomous sprayer equipped with a pair of waist-shaped charging devices. The results showed that EAAS yielded an overall average coverage of 28.4%, representing a significant 10.9% improvement over the 25.6% coverage achieved with EDAS. The overall coefficient of variation (CV) for EDAS and EAAS was 62.0% and 48.0%, respectively. Within these, the CV for the average coverage of the sample set reflecting axial distribution uniformity was 33.4% and 31.4%, respectively. Conversely, the CV for the average coverage of the sample group reflecting radial distribution uniformity was 33.7% and 17.9%, respectively. The results indicate that the waist-shaped charging device possesses remarkable charging capabilities, presenting favorable application prospects for long-range air-assisted spraying in greenhouses. The electrostatic application has a positive effect on enhancing the average coverage and improving the overall distribution uniformity. Notably, it significantly improves the radial distribution uniformity of the air-assisted spray at long range, albeit with limited improvement in the axial distribution uniformity.
The upright state of pot seedlings in the process of rice mechanized throwing operations has an important influence on the growth rate and yield of rice, and pot seedling uprightness is affected by the influence of soil backfilling during trenching. Due to the complexity of the furrow opener–soil–pot seedling interaction mechanism in the rice pot seedling planting process, the soil backfilling process is difficult to observe. In order to improve the uprightness of pot seedling planting, this paper constructs a soil model and a soil–pot seedling model step by step, based on the discrete element method (DEM), as well as a coupled model of the pot seedling planting system to study the process of furrow opener–soil–pot seedling planting, the reliability of which is then verified. The results showed that the simulation results of the constructed soil model and soil–pot seedling model deviated from the actual calibration results by <6%, and the model could accurately simulate the pot seedling throwing process. The simulation analysis of the trenching process revealed that the soil backfilling process during trenching showed a three-stage evolution pattern of “backfilling-covering-stabilizing”; in addition, the forward speed of the machine was 0.8 m/s, and the falling speed of the seedling discharge cylinder was 3.5 m/s, which made it possible for the model to simulate the pot seedling throwing process accurately. In addition, when the pot seedling with a forward speed of 0.8 m/s and a drop speed of 3.5 m/s fell into the trench after 0.15 s of trenching, its lateral and longitudinal uprightness were 67.0 ± 1.2° and 65.2 ± 1.5°, respectively. After optimization of the structure of the trenchers, the width, depth, and length of the main body were 40 mm, 37.87 mm, and 32.32 mm, respectively, and the lateral and longitudinal uprightness of the pot seedlings increased to 70.0 ± 1.0° and 69.4 ± 0.8, respectively. The coupled model bench validation test showed that its reliability error was <5%. The coupled model provides technical support for the design and parameter optimization of rice planting equipment.
A multi-rotor UAV-based oscillating-tube broadcasting device incorporating replaceable material-specific screw metering units was developed for low-rate seed and granular-fertilizer application. The key structural parameters of the oscillating tube were screened through theoretical analysis and single-factor experiments using pre-germinated conventional Huanghuazhan rice. An L16(43) orthogonal experiment was then conducted solely for exploratory screening of the main effects of flight height, forward speed, and broadcasting material on the single-pass broadcasting-uniformity coefficient of variation () and effective spreading width (We). Forward speed significantly affected , whereas all three factors significantly affected We, with flight height showing the strongest effect. Separate two-factor central composite design experiments were subsequently conducted for conventional Huanghuazhan rice, hybrid Yongyou 12 rice, Yangguang 131 rapeseed, and Stanley compound fertilizer. Material-specific quadratic models were established, yielding model-recommended flight height and forward speed combinations of 3.04 m and 2.35 m s−1, 2.79 m and 1.70 m s−1, 3.00 m and 1.80 m s−1, and 3.20 m and 2.25 m s−1, respectively. These combinations represent constrained model-based recommendations rather than global or independently verified optima. In a limited consecutive-pass field demonstration, the field-sample coefficient of variation () ranged from 13.76% to 20.34%, and the mean absolute pointwise deviation from the target count ranged from 15.11% to 19.05%. The results demonstrate the preliminary mechanical and operational feasibility of the prototype under the tested materials, operating settings, site, and environmental conditions.
Precision rice transplanting requires pot seedlings to be released intact and in a repeatable orientation for coordinated conveying and planting. This study investigated post-ejection reorientation in a cam-driven continuous picking system and proposed a root-ball-leading, shoot-trailing target orientation. Based on system kinematics, seedling mass distribution, and contact conditions, the process was divided into four stages: initial ejection, ejection-induced sliding, in-cell rotation, and post-release rotation. High-speed photography resolved stages 2–4, and the observed sequence was qualitatively consistent with the theoretical analysis. A Box–Behnken design evaluated the effects of root-ball moisture content, seedling age, and picking frequency on reorientation success rate and height. Within the tested ranges, multiresponse optimization identified a practical root-ball moisture target of 53% (maintained within ±2 percentage points), the 2.5-leaf stage, and 4 s−1 as the recommended combination. At the corresponding numerical optimum, the models predicted a reorientation success rate of 93.75% and a reorientation height of 35.08 cm, while bench confirmation at the practical setting yielded 93.33% and 33.70 cm, respectively. By focusing on post-ejection orientation under controlled bench conditions, this study provides a mechanistic and design basis for integrating continuous picking with downstream conveying and planting units in precision automated transplanting.
Mechanized rice transplanting is a key method for large-scale cultivation. To enable rapid, accurate seedling detection and evaluate rice transplanting quality, this paper proposes an improved YOLOv12n model, YOLOv12n-SCA. First, this study embeds SCA hybrid attention modules into the YOLOv12n backbone and neck networks, integrating the advantages of SCSA (Spatial and Channel Synergistic Attention) and CA (Coordinate Attention) modules to enhance the model’s ability to extract and locate seedling features against complex paddy field backgrounds. Second, clustering analysis and a plant-spacing discrimination rule, based on seedling detection coordinates, automatically identify areas with missed transplanted seedlings. Experimental results show that the YOLOv12n-SCA model achieved precision, recall, mAP@0.5, and mAP@0.5:0.95 of 93.6%, 90.3%, 95.3%, and 79.8%, respectively, with overall performance superior to that of the original YOLOv12n and single-attention-based improved models. In experiments on an independent dataset, the detection algorithm for rice seedlings in missed transplants achieved 82.34% accuracy and a counting error of 2.06%, indicating that it can effectively identify rice seedling locations and provide quality assessment results. These results show that YOLOv12n-SCA can support intelligent rice seedling detection, rice transplant quality evaluation, and smart field management in complex rice paddy environments.