Muhua Liu

Prof. Muhua Liu


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 August 2026 in Agriculture
Verified
Journal Article
Open access
PDF file
ZZZhiheng Zhu
Zhiheng Zhu
GYGuodong Yu
Guodong Yu
CCChenchen Chen
Chenchen Chen
XCXiongfei Chen
Xiongfei Chen
JCJinping Cai
Jinping Cai
PFPeng Fang
Peng Fang
A multi-rotor UAV-based oscillating-tube broadcasting device incorporating replaceable material-specific screw metering units was developed for low-rate seed and granular-fertilizer application. The key structural parameters of the oscillating tube were screened through theoretical analysis and single-factor experiments using pre-germinated conventional Huanghuazhan rice. An L16(43) orthogonal experiment was then conducted solely for exploratory screening of the main effects of flight height, forward speed, and broadcasting material on the single-pass broadcasting-uniformity coefficient of variation (CVb) and effective spreading width (We). Forward speed significantly affected CVb, whereas all three factors significantly affected We, with flight height showing the strongest effect. Separate two-factor central composite design experiments were subsequently conducted for conventional Huanghuazhan rice, hybrid Yongyou 12 rice, Yangguang 131 rapeseed, and Stanley compound fertilizer. Material-specific quadratic models were established, yielding model-recommended flight height and forward speed combinations of 3.04 m and 2.35 m s−1, 2.79 m and 1.70 m s−1, 3.00 m and 1.80 m s−1, and 3.20 m and 2.25 m s−1, respectively. These combinations represent constrained model-based recommendations rather than global or independently verified optima. In a limited consecutive-pass field demonstration, the field-sample coefficient of variation (CVf) ranged from 13.76% to 20.34%, and the mean absolute pointwise deviation from the target count ranged from 15.11% to 19.05%. The results demonstrate the preliminary mechanical and operational feasibility of the prototype under the tested materials, operating settings, site, and environmental conditions.

9 October 2026 in Plants
Verified
Journal Article
Open access
PDF file
JWJinfeng Wu
Jinfeng Wu
CLCan Li
Can Li
HHHuolong Huang
Huolong Huang
PXPeng Xu
Peng Xu
PFPeng Fang
Peng Fang
MLMuhua Liu
Muhua Liu
Precision rice transplanting requires pot seedlings to be released intact and in a repeatable orientation for coordinated conveying and planting. This study investigated post-ejection reorientation in a cam-driven continuous picking system and proposed a root-ball-leading, shoot-trailing target orientation. Based on system kinematics, seedling mass distribution, and contact conditions, the process was divided into four stages: initial ejection, ejection-induced sliding, in-cell rotation, and post-release rotation. High-speed photography resolved stages 2–4, and the observed sequence was qualitatively consistent with the theoretical analysis. A Box–Behnken design evaluated the effects of root-ball moisture content, seedling age, and picking frequency on reorientation success rate and height. Within the tested ranges, multiresponse optimization identified a practical root-ball moisture target of 53% (maintained within ±2 percentage points), the 2.5-leaf stage, and 4 s−1 as the recommended combination. At the corresponding numerical optimum, the models predicted a reorientation success rate of 93.75% and a reorientation height of 35.08 cm, while bench confirmation at the practical setting yielded 93.33% and 33.70 cm, respectively. By focusing on post-ejection orientation under controlled bench conditions, this study provides a mechanistic and design basis for integrating continuous picking with downstream conveying and planting units in precision automated transplanting.

8 September 2026 in Agriculture
Verified
Journal Article
Open access
PDF file
LFLi Fu
Li Fu
FNFengpeng Ning
Fengpeng Ning
XDXianhao Duan
Xianhao Duan
HCHailong Chen
Hailong Chen
WGWeiwei Gao
Weiwei Gao
ZLZhaopeng Liu
Zhaopeng Liu
Aiming at the path tracking oscillation problem caused by sideslip of navigation agricultural machinery in complex farmland environments, this paper takes the Yanmar YR-70D transplanter as the research object and proposes an adaptive control method based on deep belief network (DBN) sideslip identification. Based on the preview tracking model, this method dynamically adjusts the preview distance by real-time identifying the sideslip status via DBN. In this research, the Optuna framework is utilized to optimize the DBN model, and the SHAP framework is introduced to quantify the feature contribution. The results show that, considering both real-time performance and accuracy, when the combined variable of “lateral deviation + heading deviation” with a data length of 20 is adopted, the prediction accuracy of the model reaches 88.04%, among which heading deviation (HD) has the highest contribution with a SHAP value of 0.957. Comparative experiments indicate that the accuracy of DBN is comparable to that of mainstream models such as LSTM and Transformer, but its forward propagation speed (0.0487 ms) is better than other models’. Upland field experiments verify that under different test factors of vehicle speed and slope angle, the line-on time (1.83–5.60 s), line-on distance (1.46–5.07 m), and maximum overshoot (0.32–15.75 cm) of the adaptive control group are all superior to those of the fixed-parameter control group. Paddy field experiments further confirm that under the working condition of 1.0 m/s vehicle speed and 15° slope, the above three indicators of the experimental group are 0.85–3.1 s, 0.75–3.14 m and 0–7.44 cm, respectively, all of which are better than those of the control group. The proposed method demonstrated superior path tracking performance under the operating conditions of the tested rice transplanting machines, indicating its potential application in lateral slip perception adaptive navigation control. However, further verification is still needed with different types of transplanting machines, field environments, and operating conditions to assess its general applicability.