We developed a prototype of a high-Tc superconducting (HTS) linear synchronous motor (LSM) and evaluated its operational performances to obtain the preliminary design data for a test vehicle having a speed of 518.4 km/h. The HTS electromagnet was fabricated using a non-insulated (NI) GdBCO HTS coil, which was designed to produce a magnetomotive force of 300 kA-turns at a cooling temperature of 20 K. A two-stage Gifford-McMahon cryocooler was used to cool the electromagnet. The prototype was tested up to 2.7 kN sufficient to the required thrust of the test vehicle. The thrust characteristics shown by changing the operating conditions were also consistent with the simulation results. The HTS electromagnet was successfully operated during the test, and there was no fault in the NI HTS coils. Finally, we confirmed the design feasibility of HTS LSM for a test vehicle.
14 February 2018 in IEEE Transactions on Applied Superconductivity
Our research team has been developed wireless power charging (WPC) system for electric vehicle (EV) using superconducting and normal conducting resonance coils in order to improve the transfer efficiency and stability. In the practical approach, when the EV, which is installed outside, is wirelessly charged without moving. The antenna (Tx) coil is disclosed by rain or snow and so on. From this reason, the transfer characteristics surrounded aqua circumstance i.e. fresh water or salt water, should be evaluated to commercialize In addition, the high voltage wireless power charging system generates strong electromagnetic fields (EMFs) around Tx an receiver (Rx) coils. As the human safety with respect to EMFs is an important measure, it is required to identify the condition under which human exposure complies with the safety regulations. Thus, in this paper, as a fundamental approach, the spatial spots of current around Tx and Rx coils were measured. As well as, the transfer efficiencies of WPC unit under different aqua circumstances of Tx and Rx coil were measured with RF generator power of 150 W, 370 kHz.
25 March 2010 in IEEE Transactions on Applied Superconductivity
A sub-cooled liquid nitrogen system is known to be a promising method to develop a high voltage superconducting magnet. Therefore, the investigation of dielectric characteristics of gaseous electrical insulation media is important for the design of a high voltage superconducting apparatus. In this paper, dielectric characteristics of various gases according to utilization factors are investigated for the establishment of insulation design criteria of a high voltage superconducting apparatus. Dielectric experiments on gaseous nitrogen and gaseous helium (GHe) are carried out by using several kinds of sphere-to-plane electrode systems made of stainless steel. As a result, it is found that the dielectric characteristics of gas are determined by as well as gap length of electrode systems. Also, empirical expressions for electrical breakdown performance of gaseous electrical insulation media are derived and formulated. It is considered that the results of the study would be applicable to designing a high voltage superconducting apparatus.
25 February 2019 in IEEE Transactions on Applied Superconductivity
Our research team has been developed wireless pow-er charging (WPC) system for high speed superconducting mag-netic levitation (MAGLEV) train based on the strong resonance coupling method to improve the transfer efficiency and stability. Especially, the range of resonance frequency is one of main key design parameters to fabricate the system since the high reso-nance frequency can improve the transfer distance easily. On the other hand, since the sensitivity of impedance matching between antenna and receiver coils is increased in the range of higher fre-quency, the technique of stable impedance matching design in-cluding elaborated rectifying sub-circuit has been required to commercialize under high power transfer applications. From this reason, the various transfer characteristics under different rang-es for resonance frequency conditions should be evaluated to ac-complish improve the transfer efficiency. Thus, in this paper, the transfer efficiency of moving position of receiver coil (Rx) coil and consumption of liquid nitrogen were measured at of 100 and 370 kHz with 250 W, respectively. As well as, operating charac-teristics of cooled copper Rx and HTS Rx coil were evaluated un-der 100 and 370 kHz with 250 W, respectively.
3 April 2012 in IEEE Transactions on Applied Superconductivity
Recently various high temperature superconducting (HTS) conductors have been commercialized in the power applications. While a BSCCO becomes tape or wire, others coated conductors (CC) are tapes. An HTS magnet utilized with these conductors can be fabricated as a form of pancake winding or layer winding. In the case of HTS magnet using a thin and rectangular tape, the pancake winding method is satisfied in the practical cases because of its suitable features. However, one of the disadvantages of this winding method is increasing brands and splices. From this point of view, we propose a layer winding method using an HTS tape and fabricated HTS layer coils. To verify the feasibility of the proposed winding method, critical current and over-current tests are investigated in liquid nitrogen and the results are compared with those of pancake coils. In addition, operating characteristics on the condition of various winding tensions are analyzed.