Norbert Olczyk

Dr. Norbert Olczyk


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 February 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MKMaria Kaszynka
Maria Kaszynka
NONorbert Olczyk
Norbert Olczyk
MTMateusz Techman
Mateusz Techman
Szymon SkibickiSzymon Skibicki
Szymon Skibicki
Adam ZielinskiAdam Zielinski
Adam Zielinski
MHMarcin Hoffmann
Marcin Hoffmann

8 July 2020
Verified
Book Chapter
Closed access
PDF file
Szymon SkibickiSzymon Skibicki
Szymon Skibicki
MKMaria Kaszynska
Maria Kaszynska
NWNawid Wahib
Nawid Wahib
MTMateusz Techman
Mateusz Techman
KFKarol Federowicz
Karol Federowicz
Marcin HoffmannMarcin Hoffmann
Marcin Hoffmann

11 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
Szymon SkibickiSzymon Skibicki
Szymon Skibicki
MTMateusz Techman
Mateusz Techman
KFKarol Federowicz
Karol Federowicz
NONorbert Olczyk
Norbert Olczyk
Marcin HoffmannMarcin Hoffmann
Marcin Hoffmann
Few studies have focused on determining the Young’s modulus of 3D printed structures. This study presents the results of experimental investigations of Young’s modulus of a 3D printed mortar. Specimens were prepared in four different ways to investigate possible application of different methods for 3D printed structures. Study determines the influence of the number of layers on mechanical properties of printed samples. Results have shown a strong statistical correlation between the number of layers and value of Young’s modulus. The compressive strength and Young’s modulus reduction compared to standard cylindrical sample were up to 43.1% and 19.8%, respectively. Results of the study shed light on the differences between the current standard specimen used for determination of Young’s modulus and the specimen prepared by 3D printing. The community should discuss the problem of standardization of test methods in view of visible differences between different types of specimens.

15 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
NONorbert Olczyk
Norbert Olczyk
JBJarosław Błyszko
Jarosław Błyszko
MTMateusz Techman
Mateusz Techman
Non-metallic reinforcement such as fiber-reinforced polymer (FRP) is now being increasingly used in construction. Despite numerous similarities, elements reinforced with non-metallic bars work differently from the ones reinforced with steel bars, including cracking and failure mode. The examination of the stress state in these elements, so important for their proper design, raises many difficulties. The article presents the results of tests of bended beams reinforced with GFRP bars. The results of the experimental tests were compared with calculations based on selected design instructions. The results have shown that beams reinforced with GFRP exhibit increased cracking, higher deflection, and often mode of failure through crushing of concrete. The results have shown that in bended elements reinforced with the GFRP bars, the rebar often does not achieve the strength declared by the manufacturer. The study has shown that theoretical values of load-bearing capacity of beams reinforced with composite rebar differ greatly between different guidelines and instruction. The analysis showed that the use of GFRP bars as a replacement for steel bars is possible in demanding environmental conditions. However, excessive deflections and cracks may result in limited application due to overall serviceability requirements of the element.

23 February 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
NONorbert Olczyk
Norbert Olczyk
JBJarosław Błyszko
Jarosław Błyszko
MTMateusz Techman
Mateusz Techman
Adam ZielinskiAdam Zielinski
Adam Zielinski
Designed constructions must meet a certain level of safety and durability. They should also be designed in accordance to Ultimate Limit State and Serviceability Limit State with respect to profitability for the contractor. During designing stage of reinforced concrete, it is important to remember that the values in static and strength calculations are assumed as ideal. In reality, material properties of steel and particularly concrete are biased with a certain degree of random. Modern technologies allow to utilize construction materials with strictly determined deformation and mechanical parameters. Significant development of concrete technology in recent years poses new challenges. In the study, authors used Glass Fibre Reinforced Polymer rebar as a replacement for standard steel rebar. The article presents the results of the destruction tests of concrete slabs reinforced with steel and GFRP rebar. The tests were performed on 14 slabs with length-to-width ratio of 4. The thickness of slabs ranged from 6 to 10 cm. In nine slabs, authors replaced the standard rebar with GFRP rebar. The tests involved stress analysis in rebar and concrete. The secondary goal was to determine the bearing capacity and deflection of slabs and assess the cracking of the sections during load application. Composite rebar has many advantages over standard rebar. However, due to a relatively low elasticity modulus in comparison to steel, the slabs exhibit excessive deflection and cracking of bended elements.

15 May 2026 in Inżynieria i Budownictwo
Verified
Journal Article
Closed access
NONorbert Olczyk
Norbert Olczyk
KIKarolina Justyna Iwańska
Karolina Justyna Iwańska
This paper presents an analysis of the shear capacity of concrete members reinforced longitudinally with GFRP composite bars, without the use of transverse reinforcement. The calculation procedures specified in PN-EN 1992 and ACI 440.11-22 were analyzed and compared with laboratory results.