In traction control systems, it is generally required to detect vehicle speed in order to obtain the slip ratio. However, it is very difficult to measure vehicle speed directly. In this paper, novel estimation method of slip ratio is proposed without detecting the vehicle speed. The simulations and experiments both of slip ratio estimation and control are carried out by an electric vehicle to verify the proposed algorithm.
In this study, a novel system named the third-generation wireless in-wheel motor (WIWM-3), which has a dynamic wireless power transfer (DWPT) system, is developed. It can extend the cruise range, which is one of the key specifications of electric vehicles. DWPT also reduces CO2 emission as the driving resistance is reduced due to light weight of the batteries. In this study, CO2 emission by an internal combustion vehicle, a long range drivable electric vehicle with the same cruise range, and an electric vehicle with WIWM-3 equipped with the DWPT system are analyzed using actual measurement data and calculated data based on actual measurement or specification data. A WPT system with WIWM-3 achieves 92.5% DC-to-DC efficiency as indicated by an actual measurement at the nominal position. Thus, the electric vehicle with DWPT can reduce up to 62% of CO2 emission in internal combustion vehicles, and the long-range drivable vehicle emits 17% more CO2 than the electric vehicle with DWPT. Moreover, it is expected that by 2050, electric vehicles with DWPT will reduce CO2 emissions from internal combustion vehicles by 95% in Japan. DWPT systems make electric vehicles more sustainable and, hence, more acceptable for consumers.
12 July 2023 in IEEE Transactions on Power Electronics
Self-inductance variations caused by component tolerance and aging decrease the efficiency of wireless power transfer (WPT) systems. This paper deals with this issue by compensating for the self-inductance variations using pulsewidth modulation controlled switched capacitors. Previous methods relied on wireless communication between the transmitter (Tx) and receiver (Rx) to control the variable capacitors, which is not a feasible approach when considering practical constraints. This paper proposes a control scheme in which the switched capacitors are controlled simultaneously by separate closed-loops on the Tx and Rx sides, thus eliminating wireless communication. The control scheme is based on a unique condition for perfect resonance derived by focusing on the output power of the WPT circuit. This paper also points out the necessity to compensate for the self-inductance variations of both the Tx and Rx coils to achieve maximum AC/AC efficiency in battery charging applications. Furthermore, the proposed control scheme incorporates the soft switching condition of the inverter to improve the DC/DC efficiency. Experimental results of a 1-kW prototype show that the switched capacitors can flexibly adapt to the self-inductance variations and improve the AC/AC efficiency and DC/DC efficiency by up to 3.04% and 8.63%, respectively.
22 June 2023 in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
The paper proposes a method to improve the tran- sient characteristics of current overshoot and oscillation at the start of power transmission for a dynamic wireless power transfer system. The system is important to reduce the settling time as short as possible without current overshoots for a stable power supply. However, conventional methods to suppress current overshoot have a slow response on the secondary side. This paper proposes the superposition of primary and secondary responses. The proposed method controls the secondary voltage by comparing the steady-state current with the current value on the secondary side. The method can effectively suppress the oscillations in the transient response by applying the secondary voltage at the appropriate timing. This paper also studied the ro- bustness of constraints based on model analysis and experimental verification. In the experiments, the proposed method reduces the current overshoot and the settling time of the secondary current, and maximizes the receiving energy.
12 July 2022 in IEEE/ASME Transactions on Mechatronics
In vehicle motion control, the objective is to improve both dynamic performance and ride comfort through vibration analysis and compensation. Conventional drivetrains (combustion engines or on-board eletric motors) can only suppress primary modes (0.1–3 Hz) due to their limited torque response though the transmission shaft. In the case of electric vehicles with in-wheel motors (IWM), the shaft-less drivetrain enables besides primary also the active suppression of secondary ride modes (3–25 Hz). These compact and light-weight drivetrains have a higher unsprung mass, and therefore, require advanced suppression control methods that encompass both vibration regimes (0.1–25 Hz). The approach presented in this article aims to suppress the secondary ride in IWM vehicles through experimental model analysis and model-based control. In this study, the frequency characteristics of a Toyota IWM vehicle are experimentally analyzed on vibration test rigs, and subsequently, in multiple driving conditions. Based on the identified frequency responses, a model-based longitudinal acceleration control method is then analytically derived to suppress the vibration over a wide frequency band. The proposed technique is validated through experiments on Toyota's IWM prototype vehicles.
28 March 2022 in IEEE Transactions on Transportation Electrification
Research and development are active in electric vertical takeoff and landing (eVTOL) aircraft. In particular, tilt-wing eVTOL aircraft receives much attention as one of the most efficient configurations; however, they are likely to be unstable during the transition from hover to cruise because the lift and thrust have limitations depending on the airflow and tilt angle. This study proposes a new aerodynamic force control method using airflow vector estimation. The airflow vector is estimated by combining motor current, rotational speed, and Pitot-tube measurements. Aerodynamic force control is achieved through the proper design of a feedback controller using disturbance observers (DOBs) to cope with propeller-wing interference caused by the propeller slipstream. This method takes advantage of the motor control performance and is unique in which it monitors the airflow vector and actively changes the tilt angle to quickly obtain the desired acceleration. The effectiveness of the method is verified via simulations and experiments in a wind tunnel.