We report a 166 W burst mode pulse fiber amplifier seeded by a Q-switched mode-locked all-fiber laser at 1064 nm based on a fiber-coupled semiconductor saturable absorber mirror. With a pump power of 230 W at 976 nm, the output corresponds to a power conversion efficiency of 74%. The repetition rate of the burst pulse is 20 kHz, the burst energy is 8.3 mJ, and the burst duration is ∼ 20 μ s, which including about 800 mode-locked pulses at a repetition rate of 40 MHz and the width of the individual mode-locked pulse is measured to be 112 ps at the maximum output power. To avoid optical damage to the fiber, the initial mode-locked pulses were stretched to 72 ps by a bandwidth-limited fiber bragg grating. After a two-stage preamplifier, the pulse width was further stretched to 112 ps, which is a result of self-phase modulation of the pulse burst during the amplification.
We presented the chemical mask etching method to fabricate an all-fiber cladding light stripper (CLS). The morphology and density of the micron-sized microstructures generated on the fiber surface could be flexibly controlled in fabrication process, which was beneficial to the temperature performance and high-power operation capacity of the device. Based on the method, a theoretical model was developed to optimize the structure of the CLS. Initial experimental processing parameters were also obtained to realize uniform scattering and high attenuation coefficient. An all-fiber cladding light stripper with a high attenuation coefficient of 42 dB was achieved when the stripped cladding light was 1.117 kW. The temperature rising rate was only 0.011 °C/ input-Watt under the condition of air cooling, thanks to all-fiber structure and the uniform scattering design. The average stripped power density reached 9.19x10 $^6$ W/m $^2$ within a 135 mm long CLS. The CLS fabricated by this technique has great application in the high power fiber laser system.
17 December 2020 in Journal of Lightwave Technology
We present the design and fabrication of a 4×1 fiber combiner with low brightness loss. The effective area ratio (AR) of light transmission was first introduced to estimate the brightness loss. A square core fiber was used as the output fiber of the fiber combiner to achieve a high AR. The adiabatic criterion for tapering multimode fibers was investigated to obtain the structure parameters required for the fabrication. We used an auxiliary fiber of appropriate size to achieve a regular squared fiber bundle and improve bundle cutting and splicing quality. The fiber combiner yielded a high average power transmission efficiency of 97.8% when the brightness ratio was 1.05. In addition, the output power of 1030 W was obtained by combining two LDs. This type of fiber combiner can produce multi-kilowatts laser by combining high power LDs or fiber lasers. And it can be flexibly applied in laser welding, laser cladding, and laser cleaning.
We demonstrate a 150-mm long cladding light stripper for kW-level operation with high attenuation and low temperature rising. The first 100 mm of the device was designed based on theoretical simulation to achieve uniform extraction of the high power scattered cladding light and it was constructed by self-developed experimental device for continuous gradient chemical etching. While in the last 50 mm, we reduced the cladding diameter from 400 μm to 65 μm and then roughed the surface to extract the residual low NA cladding light more efficiently. The power handling capability of this design was tested up to 1.01 kW for an hour stably without causing any damage. The cladding light stripper achieved a high attenuation of 39 dB and a low temperature elevation of 0.05 °C input-Watt under the condition of air cooling. The maximum temperature on the surface of the device was only 78.5 °C with an average stripped power density of 7.156 × 106 W/m${}^2$. To the best of our knowledge, the cladding light stripper reported here has the highest average stripped power density and attenuation coefficient without compromising temperature performance. This cladding light stripper is well suitable for application in multi-kilowatts class fiber lasers.
27 January 2020 in IEEE Photonics Technology Letters
A watt-level directly diode-pumped continuous-wave (CW) Ti:Sapphire oscillator was demonstrated for the first breakthrough by a high-power green laser-diode-pumped module employing the technologies of beam shaping, beam collimation, polarization beam combining, and fiber coupling. A 1.36-W output power and 10.6% of slope efficiency were obtained based on the double-concave (DC) cavity configuration. This is the highest CW output power from Ti:Sapphire (Ti:S) oscillator directly pumped by green laser diodes (LDs) reported so far.